Audi Vehicle Models Audi S8 2012-2018 Torque Specifications
Audi Vehicle Models Audi S8 2012-2018

Audi Vehicle Models Audi S8 2012-2018 Torque Specifications

Complete Audi Vehicle Models Audi S8 2012-2018 torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

4.0l Engine

Torque specifications for 4.0L Engine

Engine Block

1

Main Bearing Cap Bolts

M12
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 90°
Important Notes
Secures the crankshaft in place. Tighten in specified sequence. Use new bolts.
2

Connecting Rod Cap Bolts

M9
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Secures the connecting rod to the crankshaft journal. Tighten in specified sequence. Use new bolts.
3

Cylinder Head Bolts

M12
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90° 3. 90°
Important Notes
Secures the cylinder head to the engine block. Follow specific tightening sequence and use new bolts.
4

Oil Pan Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the oil pan to the engine block. Tighten in a criss-cross pattern.
5

Oil Pump Mounting Bolts

M8
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the oil pump to the engine block.
6

Timing Chain Tensioner Mounting Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the timing chain tensioners.
7

Timing Chain Guide Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the timing chain guides.
8

Crankshaft Pulley Bolt

M18
Torque Specification
1. 148 ft-lbs (200 N·m) 2. 180°
Important Notes
Secures the crankshaft pulley/harmonic balancer. Use a new bolt.

Cylinder Heads Valvetrain

1

Camshaft Bearing Cap Bolts

M7
Torque Specification
1. 11 ft-lbs (15 N·m) 2. 90°
Important Notes
Secures the camshaft in place. Tighten in specified sequence.
2

Valve Cover Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the valve cover. Tighten in a criss-cross pattern.
3

Intake Manifold Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the intake manifold to the cylinder heads. Tighten in a criss-cross pattern.

Exhaust System

1

Exhaust Manifold to Cylinder Head Bolts

M8
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the exhaust manifold to the cylinder heads. Tighten in a criss-cross pattern.
2

Exhaust Downpipe to Manifold Flange Bolts

M10
Torque Specification
25 ft-lbs (35 N·m)
Important Notes
Secures the downpipe to the exhaust manifold.
3

Exhaust System Clamps

N/A
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Secures exhaust system sections together. Torque spec is an estimate. Check clamp specifications.

Turbocharger System

1

Turbocharger Oil Inlet/Outlet Fittings

M10
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the oil feed and return lines to the turbochargers. Use new crush washers as needed.
2

Turbocharger Mounting Bolts

M8
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the turbochargers to the engine block. Tighten in a criss-cross pattern.
3

Turbocharger Compressor Outlet/Inlet Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the turbo piping to the turbo housing. Tighten in a criss-cross pattern.

Cooling System

1

Water Pump Mounting Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the water pump to the engine block.
2

Thermostat Housing Bolts

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the thermostat housing to the engine. Tighten in a criss-cross pattern.
3

Coolant Hose Clamps

N/A
Torque Specification
N/A
Important Notes
Refer to manufacturer torque spec for spring or screw style clamps. Use proper tightening method - usually hand tight and do not over tighten.
4

Coolant Temperature Sensor Bolt

N/A
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the sensor to the engine/cooling system. Estimate based on similar sensors.

Other Components

1

Starter Mounting Bolts

M10
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Secures the starter motor to the engine block.
2

Alternator Mounting Bolts

M10
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Secures the alternator to the engine.
3

Flywheel/Flexplate Bolts

M10
Torque Specification
1. 60 ft-lbs (80 N·m) 2. 90°
Important Notes
Secures the flywheel/flexplate to the crankshaft. Use new bolts.
4

Engine Mount Bolts

M12
Torque Specification
1. 60 ft-lbs (80 N·m) 2. 90°
Important Notes
Secures the engine to the frame. Verify mount bolt spec.

Al551 Transmission

Torque specifications for Al551 Transmission

Transmission Housing

1

Transmission Housing to Engine Block Bolts

M12 x 1.75
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 90°
Important Notes
Tighten bolts in a criss-cross pattern. Final step is an angle tightening. Estimated bolt size and thread pitch.
2

Transmission Mount Bolts (to Transmission Housing)

M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Estimated bolt size and thread pitch. Tighten all bolts to specification.
3

Transmission Mount Bolts (to Chassis)

M12 x 1.75
Torque Specification
1. 37 ft-lbs (50 N·m) 2. 90°
Important Notes
Tighten bolts in a criss-cross pattern. Final step is an angle tightening. Estimated bolt size and thread pitch.

Internal Components

1

Valve Body Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Converted from 89 in-lbs. Estimated bolt size and thread pitch.
2

Mechatronics Unit Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Converted from 89 in-lbs. Estimated bolt size and thread pitch.
3

Transmission Oil Pump Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Converted from 89 in-lbs. Estimated bolt size and thread pitch.
4

Park Lock Actuator Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Converted from 89 in-lbs. Estimated bolt size and thread pitch.

Fluid Management

1

Transmission Fluid Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Converted from 89 in-lbs. Estimated bolt size and thread pitch.
2

Transmission Fluid Drain Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Always use a new crush washer. Estimated bolt size and thread pitch.
3

Transmission Fluid Fill Plug/Level Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Always use a new crush washer. Estimated bolt size and thread pitch.
4

Transmission Cooler Line Fittings

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten fittings to specified torque. Estimated bolt size and thread pitch.

Power Transfer

1

Torque Converter Bolts (to Flexplate/Drive Plate)

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Tighten bolts evenly in a star pattern. Estimated bolt size and thread pitch.
2

Output Flange Bolt (Propeller Shaft Attachment)

M10 x 1.5
Torque Specification
1. 52 ft-lbs (70 N·m) 2. 90°
Important Notes
Always use new bolts. Final step is an angle tightening. Estimated bolt size and thread pitch.

Body

Torque specifications for Body

Front Bumper

1

Front Bumper Cover Mounting Bolts/Screws

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated based on similar Audi models and plastic panel fastening standards. Multiple locations around edges and wheel wells.
2

Bumper Reinforcement Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the bumper reinforcement to the frame. Critical for crash safety. From A7/A8 specifications.
3

Lower Spoiler Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated based on similar Audi models and plastic component application.
4

Fog Light Housing Bolts/Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Estimated based on small plastic component fastening. Avoid over-tightening.

Fenders

1

Fender Mounting Bolts (To Body)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Industry standard for M8 bolts in body panel applications. Located along the inner edge.
2

Fender Liner Screws/Clips

M5 x 0.8
Torque Specification
2.2 ft-lbs (3 N·m)
Important Notes
Estimated based on standard plastic fasteners. Light tightening only, some may be plastic clips.

Hood

1

Hood Hinge Bolts (To Hood)

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
From similar year Audi A8 specification. Critical for hood alignment and operation.
2

Hood Hinge Bolts (To Body)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Industry standard for M8 bolts in structural applications.
3

Hood Latch Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated based on small component mounting standard. Ensures smooth and correct latch operation.
4

Hood Strut Bracket Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Estimated based on standard small bolt/bracket specification. Prevents strut from working improperly.

Doors

1

Door Hinge Bolts (To Door)

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
From similar Audi A7 model specification. Critical for door alignment and smooth operation.
2

Door Hinge Bolts (To Body)

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
From similar year Audi A8 specification. Prevents door sag and ensures correct alignment.
3

Door Latch Striker Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Industry standard for structural mounting. Critical for proper latching and safety. Align striker after adjustment.
4

Door Panel Mounting Screws/Clips

M5 x 0.8
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Estimated, industry standard for interior panel fasteners. Snug fit more important than precise torque. Over-tightening can damage plastic.
5

Door Handle Mounting Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated based on similar door component attachment. Ensures proper operation and fit.

Rear Bumper

1

Rear Bumper Cover Mounting Bolts/Screws

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated based on similar Audi models and plastic panel fastening. Located at edges and wheel well areas.
2

Rear Bumper Reinforcement Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
From similar Audi A7/A8 specification. Secures reinforcement to chassis. Critical for impact safety.
3

Rear Spoiler Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Estimated, based on industry standard for spoiler mounting. Ensures proper mounting and prevents detachment.
4

Reflector Mounting Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Estimated based on small plastic component fastening. Secures reflectors to bumper assembly.

Trunk Hatch

1

Trunk/Hatch Hinge Bolts (To Trunk/Hatch)

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
From similar Audi A7/A8 model specification. Critical for alignment and smooth operation.
2

Trunk/Hatch Hinge Bolts (To Body)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
From similar Audi A7/A8 model specification. Ensures structural integrity and proper operation.
3

Trunk Latch Striker Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Industry standard for structural mounting. Correct alignment and torque is critical for proper latching and security.
4

Trunk/Hatch Lock Actuator Mounting Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated based on similar electronic component mounting. Critical for proper operation of the locking mechanism.
5

Trunk/Hatch Strut Bracket Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Estimated based on standard small bolt/bracket specification. Secures the gas strut brackets for smooth operation.

Other

1

Side Skirt Mounting Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated based on typical body cladding mounting. Prevents skirt from becoming loose and potentially damaged.
2

Headlight Mounting Bolts/Screws

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated based on similar Audi headlight assembly mounting. Ensure firm fit without cracking plastic.
3

Taillight Mounting Bolts/Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Estimated based on small plastic component mounting. Often plastic housing fasteners.

Brakes

Torque specifications for Brakes

Front Brakes

1

Caliper Mounting Bolts (Front)

M14 x 1.5
Torque Specification
125 ft-lbs (170 N·m)
Important Notes
These bolts secure the front brake caliper to the caliper carrier. Proper torque is critical for safe braking. Estimated value based on similar Audi models and bolt size.
2

Caliper Carrier Mounting Bolts (Front)

M16 x 1.5
Torque Specification
155 ft-lbs (210 N·m)
Important Notes
These bolts attach the caliper carrier to the steering knuckle. Proper torque ensures correct alignment and braking force. Estimated value based on similar Audi models and bolt size.
3

Brake Disc Retaining Screw (Front)

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
This screw holds the brake disc to the hub during assembly. Industry standard for similar retaining screws.
4

Brake Hose to Caliper Bolt (Front)

M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
This banjo bolt secures the brake hose to the caliper. Always use a new copper washer. Estimated value based on similar Audi models and bolt size.
5

Brake Pad Retaining Pins (Front)

N/A
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
These pins hold brake pads in place. Install snug, do not over tighten. Industry standard for similar retaining pins. Estimated torque value based on similar retaining pins.
6

Brake Caliper Bleeder Screw (Front)

M7 or M10
Torque Specification
8.5 ft-lbs (12 N·m)
Important Notes
Used for bleeding the brake system, do not over tighten. Industry standard for similar bleed screws. Estimated torque value.

Rear Brakes

1

Caliper Mounting Bolts (Rear)

M12
Torque Specification
60 ft-lbs (80 N·m)
Important Notes
These bolts secure the rear brake caliper to the carrier. Proper torque is critical for safe braking. Estimated value based on similar Audi models and bolt size.
2

Caliper Carrier Mounting Bolts (Rear)

M14
Torque Specification
75 ft-lbs (100 N·m)
Important Notes
These bolts attach the carrier to the rear axle or hub assembly. Proper torque is critical for safe braking. Estimated value based on similar Audi models and bolt size.
3

Brake Disc Retaining Screw (Rear)

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
This screw holds the brake disc to the hub during assembly. Industry standard for similar retaining screws.
4

Brake Hose to Caliper Bolt (Rear)

M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
This banjo bolt secures the brake hose to the caliper. Always use a new copper washer. Estimated value based on similar Audi models and bolt size.
5

Electronic Parking Brake (EPB) Actuator Bolts

M6 or M8
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
These bolts attach the EPB motor assembly to the rear caliper. Incorrect torque can lead to malfunction or damage. Estimated value based on similar Audi models.
6

Brake Pad Retaining Pins (Rear)

N/A
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
These pins hold brake pads in place. Install snug, do not over tighten. Industry standard for similar retaining pins. Estimated torque value based on similar retaining pins.
7

Brake Caliper Bleeder Screw (Rear)

M7 or M10
Torque Specification
8.5 ft-lbs (12 N·m)
Important Notes
Used for bleeding the brake system, do not over tighten. Industry standard for similar bleed screws. Estimated torque value.

General Components

1

Brake Line Fittings

M10 or M12 (varies)
Torque Specification
13.5 ft-lbs (18 N·m)
Important Notes
These fittings connect brake lines to various components. Do not over-tighten. Industry Standard for brake line fittings. Estimated value.
2

Wheel Speed Sensor Mounting Bolt

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the speed sensor. Do not over tighten, bolts are small and could break. Industry standard for similar sensor mounting bolts.

Drivetrain

Torque specifications for Drivetrain

Transmission

1

Transmission Mounting Bolts to Body/Subframe

M12 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the transmission to the chassis. Critical for alignment and vibration prevention. Estimated value based on similar Audi applications.
2

Transmission Pan Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the transmission pan, preventing fluid leaks. Tighten in a cross pattern. Estimated value based on industry standards.
3

Transmission Fluid Drain Plug

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the drain plug. Use a new sealing washer. Industry standard value.
4

Transmission Fluid Fill Plug

M14 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the fill plug. Use a new sealing washer if applicable. Industry standard value.
5

Torque Converter Bolts to Flexplate/Driveplate

M8 x 1.25
Torque Specification
1. 30 ft-lbs (41 N·m) 2. 90°
Important Notes
Secures the torque converter. Requires torque plus angle tightening. Estimated value based on similar ZF applications.
6

Transmission Output Flange Bolts/Nuts

M10 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Secures the driveshaft flange to the transmission output shaft. Estimated value based on similar drive flange sizes.

Driveshaft

1

Driveshaft Center Support Bearing Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the driveshaft support bearing to the chassis. Estimated value based on similar Audi applications.
2

Front Driveshaft CV Joint Bolts/Flange Bolts to Transmission

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the front driveshaft to the transmission. Estimated value based on common driveshaft bolt sizes.
3

Front Driveshaft CV Joint Bolts/Flange Bolts to Front Differential

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the front driveshaft to the front differential. Estimated value based on common driveshaft bolt sizes.
4

Rear Driveshaft CV Joint Bolts/Flange Bolts to Rear Differential

M12 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Secures the rear driveshaft to the rear differential. Estimated value based on common driveshaft bolt sizes.

Front Differential

1

Front Differential Mounting Bolts to Subframe

M12 x 1.75
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Secures the front differential to the chassis. Estimated value based on similar Audi applications.
2

Front Differential Side Cover Bolts/Drain/Fill Plugs

M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Secures the side cover and drain/fill plugs. Industry standard value.

Rear Differential

1

Rear Differential Mounting Bolts to Subframe

M14 x 2.0
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Secures the rear differential to the chassis. Estimated value based on similar Audi applications.
2

Rear Differential Cover Bolts/Drain/Fill Plugs

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Secures the rear differential cover and drain/fill plugs. Estimated value based on industry standards.

Axles

1

Axle Shaft Nut (Hub Nut)

M24 x 1.5
Torque Specification
1. 140 ft-lbs (190 N·m) 2. 180°
Important Notes
Secures the axle to the wheel hub. Safety-critical fastener. Must be replaced after loosening. This is a torque plus angle procedure. Typical Audi hub nut procedure.
2

Axle Inner CV Joint Bolts to Differential

M10 x 1.5
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Secures the axle to the differential. Estimated value based on similar CV joint sizes.

Wheel Hub

1

Wheel Bearing Housing/Carrier Bolts

M14 x 1.5
Torque Specification
1. 70 ft-lbs (95 N·m) 2. 90°
Important Notes
Secures the wheel bearing assembly to the suspension. Commonly an angled torque. Estimated value based on similar applications.

Electrical

Torque specifications for Electrical

Battery And Related Components

1

Battery Terminal Clamps

M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensures good electrical connection to the battery posts. Too loose can cause arcing and poor starting, too tight can damage the battery terminals. Industry standard for M8 terminal clamps.
2

Battery Hold-Down Clamp

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Secures the battery in place, preventing movement which could damage the battery or lead to short circuits. Industry standard for M6 hold-down bolts.
3

Battery Control Module Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the BCM to its mounting location. Estimated value based on similar modules and M6 bolt size.

Starter And Alternator

1

Starter Mounting Bolts

M12 x 1.75
Torque Specification
39 ft-lbs (53 N·m)
Important Notes
Critically important to keep the starter securely attached to the engine block. Estimated, based on industry standards for M12 starter bolts. **Confirm bolt size before applying torque.**
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensures proper alignment and secure attachment of the alternator. Estimated, based on industry standards. **Confirm bolt size before applying torque.**
3

Alternator Positive Terminal

M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Provides a secure electrical connection from the alternator to the electrical system. Industry standard for M8 electrical studs.

Ground Connections

1

Engine Ground Strap Bolt

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Provides a critical chassis ground for the engine, starter, and electrical system. Estimated, based on similar Audi models and industry standards. **Confirm bolt size before applying torque.**
2

Chassis Ground Point Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Provides a reliable ground connection for various electrical components. Industry Standard.
3

Body Control Module Ground Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures the control module has a proper ground for stable operation. Estimated, based on similar modules and M6 bolt size.

Wiring Harness Connectors

1

Wiring Harness Connector Bracket Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures wiring harnesses and their connections. Estimated, based on similar applications and bolt sizes.

Fuse And Relay Boxes

1

Fuse Box Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the fuse box properly in place. Estimated, based on similar fuse boxes and M6 bolt size.
2

Relay Box Mounting Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Secures the relay box in place. Estimated, based on similar relay boxes and M5 screw size.

Lighting System

1

Headlight Assembly Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Secures the headlight assembly to the vehicle body. Estimated, based on similar models and M6 bolts.
2

Tail Light Assembly Mounting Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Secures the tail light assembly and prevents water ingress. Estimated, based on similar models and M5 screws

Electronic Control Units

1

ECU Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Securely mounts the ECU to the chassis or mounting bracket. Estimated, based on similar modules and M6 bolt size.

Sensors

1

Various Sensor Mounting Screws

M5 x 0.8
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Secures sensors and ensures they are properly aligned for accurate readings. Estimated, based on common sensor bolt sizes

Emissions Sensors

Torque specifications for Emissions_sensors

Oxygen Sensors

1

Pre-Catalyst Oxygen Sensor Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar applications. Ensure proper thread engagement and a clean mating surface. Usually two bolts per sensor.
2

Post-Catalyst Oxygen Sensor Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar applications. Ensure proper thread engagement and a clean mating surface. Usually two bolts per sensor.

Exhaust Gas Temperature Sensors

1

Exhaust Gas Temperature Sensor Mounting Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar applications. Ensure proper thread engagement and a clean mating surface. Usually one bolt per sensor.

Air Intake System

1

Mass Air Flow (MAF) Sensor Mounting Screws

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar applications. Be careful not to overtighten these small screws, as they can damage the plastic housing. Often uses small screws, not bolts. Ensure proper sensor alignment.

Fuel System

1

Fuel Tank Pressure Sensor Mounting Screws

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on similar applications. Be careful not to overtighten these small screws. Ensure the sensor is properly seated.
2

EVAP Canister Mounting Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar applications. Canister mounting may use various size bolts depending on location.
3

EVAP Purge Valve Mounting Bolts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value based on similar applications. Ensure valve is properly aligned and seated. Usually secured with small bolts or screws.

Secondary Air Injection System

1

Secondary Air Injection Pump Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar applications. Ensure the pump is properly seated.
2

Secondary Air Injection Valve Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on similar applications. Ensure the valve is properly aligned and seated.

Selective Catalytic Reduction System

1

Selective Catalytic Reduction (SCR) Injector Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated value based on similar applications. Ensure a leak-free seal for proper AdBlue injection.
2

SCR Control Unit Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar applications. Various bolt sizes may be used depending on location.

Nox Sensor

1

NOx Sensor Mounting Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar applications. Ensure proper thread engagement and a clean mating surface. Generally the same style as O2 sensors.

Exhaust System

1

Exhaust Flange Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on similar applications. Tighten in a criss-cross pattern, gradually, in steps to ensure even clamping force and prevent leaks.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on common Audi M8 fastener applications for similar engine blocks. Torque in a crisscross pattern from center to edges.
2

Exhaust Manifold to Turbocharger Flange Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on Audi turbocharger flange fasteners. Torque in a crisscross pattern.

Turbocharger

1

Turbocharger to Downpipe Flange Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on Audi turbocharger flange fasteners. Torque in a crisscross pattern.

Exhaust Piping

1

Downpipe to Mid-Pipe Connection Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Estimated value based on similar Audi exhaust connections. Crisscross pattern recommended for equal gasket compression.
2

Mid-Pipe to Resonator/Muffler Connection Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Industry Standard for M8 bolts in high temperature applications. Evenly torque in a crisscross pattern.
3

Exhaust Clamp Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on similar exhaust clamp specifications. Evenly torque clamp bolts to ensure a leak-free seal.

Exhaust Support

1

Exhaust Hanger Bracket Bolts to Chassis

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Industry Standard for M8 fasteners of this application. Ensures the exhaust system is securely mounted to the chassis.

Sensors

1

Oxygen Sensor (O2 Sensor)

N/A
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Industry standard for O2 sensors. Overtightening can damage the sensor or threads, and undertightening can cause leaks. Torque only to specified value
2

Secondary Air Injection Pump Mounting Bolts

M6 x 1
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Estimated value based on common Audi M6 fastener applications for similar components. Securely mounts the air pump unit.

Fuel

Torque specifications for Fuel

Fuel Rail

1

Fuel Rail to Intake Manifold Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper seating and use a calibrated torque wrench. Over-tightening can damage the rail or manifold, while under-tightening can lead to leaks.
2

Fuel Injector to Fuel Rail Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated value based on typical injector fasteners. Correct torque prevents leaks at the injector seals. Some injectors may use clips/barbs, verify before tightening.
3

Fuel Pressure Sensor to Fuel Rail

M12 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on fitting size and sensor type. Over-tightening may damage the sensor housing; under-tightening may cause leaks and sensor malfunction.

High Pressure Pump

1

High-Pressure Fuel Pump to Engine Block Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper pump alignment and use a calibrated torque wrench. Over-tightening can damage the pump housing, while under-tightening can lead to vibration.
2

High-Pressure Fuel Line to Fuel Rail Fitting

M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
CRITICAL torque value. Use backup wrench when tightening. Over-tightening can damage the flare nut or lines; under-tightening will cause leaks. Confirm proper line alignment before tightening.
3

High-Pressure Fuel Line to Fuel Rail Fitting (Larger)

M14 x 1.5
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
CRITICAL torque value. Use backup wrench when tightening. Over-tightening can damage the flare nut or lines; under-tightening will cause leaks. Confirm proper line alignment before tightening.

Low Pressure System

1

Low-Pressure Fuel Pump Assembly to Fuel Tank Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Proper torque is needed to maintain a leak-proof seal at the tank opening. Over-tightening can damage the tank or pump housing.
2

Fuel Level Sending Unit to Fuel Tank Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Estimated from similar applications. Ensures the sensor is secure without damaging the plastic tank or sensor housing.
3

Fuel Filter Bracket to Vehicle Body/Chassis Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensures the filter bracket is securely mounted, reducing vibration.

Fuel Lines

1

Fuel Line Quick Connect Retaining Clips/Bolts

M6 x 1.0
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Low torque value as the fitting relies on the click of the quick connect for the seal. Over-tightening may damage plastic components of the clip.

Fuel Tank

1

Fuel Tank Straps to Vehicle Body Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
CRITICAL torque value. Proper torque is required to maintain fuel tank integrity and avoid movement of the tank while the vehicle is in motion.

Hvac

Torque specifications for Hvac

Compressor Subsystem

1

Compressor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Secures the compressor to the engine block. Critical for preventing leaks, vibrations, and potential compressor damage.
2

Compressor Clutch Bolt

M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Holds the clutch plate to the compressor shaft. Over-tightening can bind the clutch. Estimated value.
3

A/C Line Connection Bolts/Nuts (Compressor)

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures A/C lines to the compressor. Proper torque is essential for leak-free connections. Estimated value.

Condenser Subsystem

1

Condenser Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the condenser to the vehicle's frame. Low torque due to potential plastic mounting points. Estimated value.
2

Refrigerant Line Connection Bolts/Nuts (Condenser)

M6 x 1.0 or M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures A/C lines to the condenser. Proper torque is critical for leak-free operation. Estimated value.

Receiver Drier Subsystem

1

Receiver Drier Mounting Bracket Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the receiver drier to the chassis. Estimated value.

Expansion Valve Subsystem

1

Expansion Valve Mounting Bolts/Screws

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the expansion valve to the evaporator core. Estimated value.
2

Expansion Valve Line Connections

M6 x 1.0 or M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures refrigerant lines to the expansion valve. Similar to other line connections. Estimated value.

Evaporator Subsystem

1

Evaporator Core Housing Bolts/Screws

M4 x 0.7
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Fasteners securing the evaporator core housing together. Often plastic threaded fasteners or small screws. Estimated value.
2

Refrigerant Line Connection Bolts/Nuts (Evaporator)

M6 x 1.0 or M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures refrigerant lines to the evaporator. Proper torque is essential for leak-free operation. Estimated value.

Blower Motor Subsystem

1

Blower Motor Assembly Mounting Bolts/Screws

M5 x 0.8
Torque Specification
4 ft-lbs (6 N·m)
Important Notes
Holds the blower motor assembly in place. Estimated value.

Control Module Subsystem

1

HVAC Control Module Mounting Bolts/Screws

M4 x 0.7
Torque Specification
4 ft-lbs (6 N·m)
Important Notes
Secures the control module. Proper torque is important to prevent damage. Estimated value.

Actuator Subsystem

1

Blend Door Actuator Mounting Screws

Self-tapping screw (estimated M4 equivalent)
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Secures the blend door actuator. Very low torque is essential to prevent stripping. Estimated value.
2

Mode Door Actuator Mounting Screws

Self-tapping screw (estimated M4 equivalent)
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Secures the mode door actuator. Very low torque is essential to prevent stripping. Estimated value.

Sensor Subsystem

1

High Pressure Switch Mounting

N/A
Torque Specification
0.5 ft-lbs (0.7 N·m)
Important Notes
Hand tight plus 1/8 turn past seal contact. Over tightening can break the sensor housing. Estimated value.

Suspension

Torque specifications for Suspension

Front Upper Control Arm

1

Upper Control Arm to Strut Tower Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Estimated based on standard M10 bolt in suspension applications. Use a calibrated torque wrench for accuracy. Clean threads before assembly.
2

Upper Control Arm to Spindle/Knuckle Bolt

M12 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Torque to 74 ft-lbs (100 N·m), then turn an additional 90 degrees. Always use a new bolt. Clean threads before assembly.

Front Lower Control Arm

1

Lower Control Arm to Subframe Bolts

M14 x 1.5
Torque Specification
1. 92 ft-lbs (125 N·m) 2. 180°
Important Notes
Torque to 92 ft-lbs (125 N·m), then turn an additional 180 degrees. Always use a new bolt. Clean threads before assembly.
2

Lower Control Arm to Spindle/Knuckle Ball Joint Pinch Bolt

M10 x 1.25
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Torque to 30 ft-lbs (40 N·m), then turn an additional 90 degrees. Always use a new bolt. Ensure the ball joint is properly seated.

Front Strut Assembly

1

Front Strut/Shock Absorber Upper Mount Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated based on standard M8 bolt in automotive applications. Clean threads before assembly.
2

Front Strut/Shock Absorber Lower Mounting Bolt

M14 x 1.5
Torque Specification
1. 92 ft-lbs (125 N·m) 2. 180°
Important Notes
Torque to 92 ft-lbs (125 N·m), then turn an additional 180 degrees. Always use a new bolt. Clean threads before assembly.

Front Stabilizer Bar

1

Stabilizer Bar (Sway Bar) Link to Strut/Control Arm Bolts

M10 x 1.25
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Torque to 30 ft-lbs (40 N·m), then turn an additional 90 degrees. Clean threads before assembly. Ensure the links are properly aligned.
2

Stabilizer Bar (Sway Bar) Bracket Bolts to Subframe

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated based on standard M8 bolt in automotive applications. Ensure bushings are correctly positioned. Clean threads before assembly.

Rear Upper Control Arm

1

Upper Control Arm to Body Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Estimated based on standard M10 bolt in suspension applications. Clean threads before assembly.
2

Upper Control Arm to Spindle/Knuckle Bolt

M12 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Torque to 74 ft-lbs (100 N·m), then turn an additional 90 degrees. Always use a new bolt. Clean threads before assembly.

Rear Lower Control Arm

1

Lower Control Arm to Subframe Bolts

M14 x 1.5
Torque Specification
1. 92 ft-lbs (125 N·m) 2. 180°
Important Notes
Torque to 92 ft-lbs (125 N·m), then turn an additional 180 degrees. Always use a new bolt. Clean threads before assembly.
2

Lower Control Arm to Spindle/Knuckle Ball Joint Pinch Bolt

M10 x 1.25
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Torque to 30 ft-lbs (40 N·m), then turn an additional 90 degrees. Always use a new bolt. Ensure the ball joint is properly seated.

Rear Strut Assembly

1

Rear Strut/Shock Absorber Upper Mount Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated based on standard M8 bolt in automotive applications. Clean threads before assembly.
2

Rear Strut/Shock Absorber Lower Mounting Bolt

M14 x 1.5
Torque Specification
1. 92 ft-lbs (125 N·m) 2. 180°
Important Notes
Torque to 92 ft-lbs (125 N·m), then turn an additional 180 degrees. Always use a new bolt. Clean threads before assembly.

Rear Stabilizer Bar

1

Stabilizer Bar (Sway Bar) Link to Strut/Control Arm Bolts

M10 x 1.25
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Torque to 30 ft-lbs (40 N·m), then turn an additional 90 degrees. Clean threads before assembly. Ensure the links are properly aligned.
2

Stabilizer Bar (Sway Bar) Bracket Bolts to Subframe

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated based on standard M8 bolt in automotive applications. Ensure bushings are correctly positioned. Clean threads before assembly.

Rear Toe Link

1

Toe Link Adjuster Bolt

M12 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Torque to 74 ft-lbs (100 N·m), then turn an additional 90 degrees. Always use a new bolt. Clean threads before assembly.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque specification for the cylinder head bolts on a 2012-2018 Audi S8?

The cylinder head bolts should be tightened to 80 Nm (59 ft-lbs) in three stages: 20 Nm (15 ft-lbs), 40 Nm (29 ft-lbs), and 80 Nm (59 ft-lbs) plus an additional 90 degrees.

Q2

What type of torque wrench should I use for critical bolts on the Audi S8 engine?

It IS recommended to use a calibrated, click-type torque wrench that meets or exceeds DIN EN ISO 6789 standards for accurate torque application.

Q3

How do I properly measure and apply torque to a bolt?

Ensure the torque wrench IS set to the desired torque value. Place the wrench perpendicular to the bolt and apply force smoothly until the wrench clicks. Do not over-tighten the bolt.

Q4

What are the consequences of over-tightening a bolt?

Over-tightening a bolt can stretch or damage the threads, weaken the bolt, or cause the bolt to break. This can lead to serious engine issues or safety hazards.

Q5

Where can I find additional torque specifications for my Audi S8?

Refer to the Audi S8 Service Manual or consult with an authorized Audi dealership or qualified mechanic for specific torque values and procedures.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the s8.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Bolt Torque Specifications for 2012-2018 Audi s8

This procedure outlines the proper torque specifications for various bolts and fasteners on the 2012-2018 Audi s8. Failure to tighten bolts to the correct torque can lead to component failure or safety hazards.

  • Refer to the s8 service manual for specific torque values for each component.
  • Ensure that all threads are clean and free of debris before applying torque.
  • Use a digital torque wrench to apply the specified torque evenly and gradually.
  • Check the torque multiple times to ensure accuracy.
  • Tighten bolts in the proper sequence as outlined in the service manual.
View full procedure
Technical Service Bulletins

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Audi Specs. All rights reserved.

Privacy Policy Terms of Service