Audi Vehicle Models Audi Q8 2018-present
Audi Vehicle Models Audi Q8 2018-present Torque Specifications
Complete Audi Vehicle Models Audi Q8 2018-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
3.0l Engine
Torque specifications for 3.0L Engine
3.0l Engine
Torque specifications for 3.0L Engine
Cylinder Head
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 90°
3. 90°
Important Notes
Torque-to-yield bolts. Use a three-stage torque sequence. Always replace bolts when removed. Torque in the correct sequence for even clamping force. Estimated bolt size.
2 Camshaft Bearing Cap Bolts
M6 x 1.0
2
Camshaft Bearing Cap Bolts
M6 x 1.0
Torque Specification
1. 7 ft-lbs (10 N·m)
2. 90°
Important Notes
Tighten bolts evenly. Use a two-stage torque sequence, followed by a 90 degree angle turn. Estimated bolt size.
Intake System
1 Intake Manifold Bolts
M6 x 1.0
1
Intake Manifold Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque. Use a crisscross pattern to tighten.
2 Throttle Body Bolts
M6 x 1.0
2
Throttle Body Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque. Use a crisscross pattern to tighten.
Exhaust System
1 Exhaust Manifold Bolts
M8 x 1.25
1
Exhaust Manifold Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts evenly to prevent leaks. Estimated bolt size. Use a crisscross pattern to tighten.
2 Exhaust Downpipe Bolts (Engine Side)
M8 x 1.25
2
Exhaust Downpipe Bolts (Engine Side)
M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten bolts evenly to prevent exhaust leaks. Estimated bolt size and torque.
3 Exhaust System Clamp Bolts
M8 x 1.25
3
Exhaust System Clamp Bolts
M8 x 1.25
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque.
4 Oxygen Sensor
M18 x 1.5
4
Oxygen Sensor
M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten to avoid exhaust leaks. Industry standard.
Lubrication System
1 Oil Pan Bolts
M6 x 1.0
1
Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly to prevent oil leaks. Estimated bolt size.
2 Oil Pump Bolts
M8 x 1.25
2
Oil Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque.
3 Oil Filter Housing Bolts
M6 x 1.0
3
Oil Filter Housing Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly to prevent leaks. Estimated bolt size.
Cooling System
1 Water Pump Bolts
M6 x 1.0
1
Water Pump Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly to prevent coolant leaks. Estimated bolt size.
2 Thermostat Housing Bolts
M6 x 1.0
2
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts evenly to prevent coolant leaks. Estimated bolt size.
Engine Accessories
1 Alternator Mounting Bolts
M8 x 1.25
1
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque.
2 Starter Mounting Bolts
M8 x 1.25
2
Starter Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque.
3 Power Steering Pump Mounting Bolts
M8 x 1.25
3
Power Steering Pump Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque.
4 A/C Compressor Mounting Bolts
M8 x 1.25
4
A/C Compressor Mounting Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size and torque.
Engine Mounts
1 Engine Mount Bolts (To Engine)
M10 x 1.5
1
Engine Mount Bolts (To Engine)
M10 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
Torque to yield bolts, use two stage torque sequence. Always replace bolts when removed. Estimated bolt size.
2 Engine Mount Bolts (To Frame)
M10 x 1.5
2
Engine Mount Bolts (To Frame)
M10 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
Torque to yield bolts, use two stage torque sequence. Always replace bolts when removed. Estimated bolt size.
Timing System
1 Timing Chain Tensioner Bolts
M8 x 1.25
1
Timing Chain Tensioner Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts evenly. Estimated bolt size.
2 Timing Chain Guides
M6 x 1.0
2
Timing Chain Guides
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten evenly. Estimated bolt size.
Flywheel Flexplate
1 Flywheel/Flexplate Bolts
M10 x 1.5
1
Flywheel/Flexplate Bolts
M10 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
Torque to yield bolts. Use a two-stage torque sequence. Always replace bolts when removed. Estimated bolt size.
Crankshaft Bottom End
1 Crankshaft Main Bearing Bolts
M12 x 1.5
1
Crankshaft Main Bearing Bolts
M12 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 90°
Important Notes
Torque to yield bolts. Use a two-stage torque sequence. Always replace bolts when removed. Estimated bolt size.
2 Connecting Rod Bolts
M9 x 1.25
2
Connecting Rod Bolts
M9 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 45°
Important Notes
Torque to yield bolts. Use a two-stage torque sequence. Always replace bolts when removed. Estimated bolt size.
Body
Torque specifications for Body
Body
Torque specifications for Body
Front End And Hood
1 Hood Hinge Bolts
M8 x 1.25
1
Hood Hinge Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the hood to the chassis. Proper torque ensures smooth operation and prevents misalignment. Safety-critical.
2 Hood Latch Bolts
M6 x 1.0
2
Hood Latch Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Attaches the latch mechanism to the hood or chassis. Ensures secure closing and opening. Safety-critical. Estimated based on similar applications.
3 Front Bumper Cover Mounting Bolts
M6 x 1.0
3
Front Bumper Cover Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the bumper cover to the front structure and/or bumper reinforcement. Prevents vibrations and detachment.
4 Headlight Mounting Bolts
M6 x 1.0
4
Headlight Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Attaches the headlight assembly to the front structure. Proper torque ensures correct aiming and alignment.
5 Fender Mounting Bolts
M6 x 1.0
5
Fender Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures fenders to the body frame. Necessary for correct alignment and panel fit. Estimated based on similar applications.
6 Radiator Support Bolts
M8 x 1.25
6
Radiator Support Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the radiator support (core support) to the chassis. Provides structural support for cooling and front end components. Safety-critical.
7 Wheel Well Liner Bolts/Screws
Self-tapping or plastic rivets
7
Wheel Well Liner Bolts/Screws
Self-tapping or plastic rivets
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Secures the fender liner. Prevents debris from entering the engine bay and protects inner body components. Hand tighten using manufacturer-specified fasteners. This is an estimated value; use specified fasteners. Do not overtighten.
Door System
1 Door Hinge Bolts
M10 x 1.5
1
Door Hinge Bolts
M10 x 1.5
Torque Specification
45 ft-lbs (60 N·m)
Important Notes
Secures the doors to the chassis. Critical for door alignment and preventing sagging. Safety-critical.
2 Door Latch Mechanism Bolts
M6 x 1.0
2
Door Latch Mechanism Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the latch to the door. Ensures proper closing and locking functionality. Safety-critical.
3 Door Handle Mounting Bolts
M5 x 0.8
3
Door Handle Mounting Bolts
M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Attaches the exterior door handle. Proper torque ensures secure operation of handle. Estimated value.
4 Door Panel Mounting Screws
Self-tapping, various sizes
4
Door Panel Mounting Screws
Self-tapping, various sizes
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Secures the interior door panel. Over-tightening can damage the plastic. Hand tighten and do not overtighten. This is an estimated value.
5 Window Regulator Bolts
M6 x 1.0
5
Window Regulator Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Attaches the window regulator to the door frame. Ensures proper window operation.
Rear End And Hatch
1 Tailgate/Hatch Hinge Bolts
M10 x 1.5
1
Tailgate/Hatch Hinge Bolts
M10 x 1.5
Torque Specification
45 ft-lbs (60 N·m)
Important Notes
Secures the tailgate/hatch to the chassis. Critical for smooth operation and proper alignment. Safety-critical.
2 Tailgate/Hatch Latch Mechanism Bolts
M6 x 1.0
2
Tailgate/Hatch Latch Mechanism Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the latch to the tailgate or chassis. Ensures proper closing and locking of the hatch. Safety-critical. Estimated based on similar applications.
3 Rear Bumper Cover Mounting Bolts
M6 x 1.0
3
Rear Bumper Cover Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the rear bumper cover to the rear structure. Prevents vibrations and detachment.
4 Tail Light Mounting Bolts
M6 x 1.0
4
Tail Light Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Attaches the tail light assembly to the rear body. Ensures correct fitment and alignment of the lights.
Body Panels And Other
1 Rocker Panel Bolts
M6 x 1.0
1
Rocker Panel Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures rocker panels to the body frame. Proper torque prevents rattles and misalignment. Estimated based on similar applications.
2 Roof Panel Trim/Attachment Bolts
M6 x 1.0
2
Roof Panel Trim/Attachment Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures trim and roof components to the roof structure. Estimated based on similar applications.
3 Seat Mounting Bolts
M10 x 1.5
3
Seat Mounting Bolts
M10 x 1.5
Torque Specification
1. 40 ft-lbs (55 N·m)
2. 90°
Important Notes
Critical for seat safety. Uses an angle-tightening procedure after initial torque. Safety-critical. Angle tightening is CRITICAL and must be followed.
4 Seatbelt Anchor Bolts
M10 x 1.5
4
Seatbelt Anchor Bolts
M10 x 1.5
Torque Specification
1. 40 ft-lbs (55 N·m)
2. 90°
Important Notes
Safety-critical. Ensures proper restraint during an impact. Angle tightening is essential to achieve proper bolt stretch and tension. Angle tightening is CRITICAL and must be followed.
5 Interior Trim Mounting Screws
Self-tapping or plastic clips, various sizes
5
Interior Trim Mounting Screws
Self-tapping or plastic clips, various sizes
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Secures interior panels and trim. Over-tightening can cause damage. Hand tighten and do not overtighten. Estimated value.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Front Caliper
1 Caliper Guide Pin Bolts (Front)
M10 x 1.25
1
Caliper Guide Pin Bolts (Front)
M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the brake caliper to the caliper carrier, allowing it to slide during braking. Ensure smooth pin movement and proper thread engagement.
2 Caliper Mounting Bracket Bolts (Front)
M14 x 1.5
2
Caliper Mounting Bracket Bolts (Front)
M14 x 1.5
Torque Specification
1. 133 ft-lbs (180 N·m)
2. 90°
Important Notes
These are torque-to-yield bolts that must be replaced after removal. Tighten to specified torque and then further tighten by an additional 90 degrees. It is critical to follow torque and angle steps correctly for proper bracket clamping force.
3 Brake Line Banjo Bolt (Front Caliper)
M10 x 1.0
3
Brake Line Banjo Bolt (Front Caliper)
M10 x 1.0
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Secures the brake line to the caliper. Always use new crush washers for proper sealing to avoid leaks. Over-tightening can damage the banjo fitting or caliper.
4 Brake Pad Wear Sensor Screw (Front)
M4 x 0.7
4
Brake Pad Wear Sensor Screw (Front)
M4 x 0.7
Torque Specification
3.7 ft-lbs (5 N·m)
Important Notes
Secures the wear sensor wiring harness to the caliper. Over-tightening could damage the sensor. This is an estimated value.
Front Rotor
1 Brake Disc Retaining Screw (Front)
M6 x 1.0
1
Brake Disc Retaining Screw (Front)
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
These small screws hold the brake rotor in place during wheel changes. Estimated value.
Front Abs
1 ABS Sensor Bolt (Front)
M6 x 1.0
1
ABS Sensor Bolt (Front)
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the ABS sensor to the hub or knuckle. Estimated value based on similar sensor bolts. Do not over-tighten, as sensor could be damaged.
Rear Caliper
1 Caliper Guide Pin Bolts (Rear)
M10 x 1.25
1
Caliper Guide Pin Bolts (Rear)
M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the brake caliper to the caliper carrier. Similar to the front. Ensure smooth pin movement.
2 Caliper Mounting Bracket Bolts (Rear)
M14 x 1.5
2
Caliper Mounting Bracket Bolts (Rear)
M14 x 1.5
Torque Specification
1. 133 ft-lbs (180 N·m)
2. 90°
Important Notes
These are torque-to-yield bolts that must be replaced after removal. Tighten to specified torque and then further tighten by an additional 90 degrees. It is critical to follow torque and angle steps correctly for proper bracket clamping force.
3 Electronic Parking Brake Motor Bolts (Rear)
M8 x 1.25
3
Electronic Parking Brake Motor Bolts (Rear)
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the electronic parking brake motor to the rear caliper. Proper torque is crucial for correct functionality.
4 Brake Line Banjo Bolt (Rear Caliper)
M10 x 1.0
4
Brake Line Banjo Bolt (Rear Caliper)
M10 x 1.0
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Secures the brake line to the caliper. Always use new crush washers for proper sealing to avoid leaks.
5 Brake Pad Wear Sensor Screw (Rear)
M4 x 0.7
5
Brake Pad Wear Sensor Screw (Rear)
M4 x 0.7
Torque Specification
3.7 ft-lbs (5 N·m)
Important Notes
Secures the wear sensor wiring to the caliper. Over-tightening could damage the sensor. This is an estimated value.
Rear Rotor
1 Brake Disc Retaining Screw (Rear)
M6 x 1.0
1
Brake Disc Retaining Screw (Rear)
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
These small screws hold the brake rotor in place during wheel changes. Estimated value.
Rear Abs
1 ABS Sensor Bolt (Rear)
M6 x 1.0
1
ABS Sensor Bolt (Rear)
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the ABS sensor to the hub or knuckle. Estimated value based on similar sensor bolts. Do not over-tighten, as sensor could be damaged.
Dl382 Transmission
Torque specifications for Dl382 Transmission
Dl382 Transmission
Torque specifications for Dl382 Transmission
Transmission Housing
1 Main Case Halves Bolts
M10 x 1.5
1
Main Case Halves Bolts
M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m)
2. 90°
Important Notes
Estimated value based on similar transmissions. Torque sequence should be followed. Use new bolts where specified.
Mechatronic Unit
1 Mechatronic Unit Mounting Bolts
M6 x 1.0
1
Mechatronic Unit Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten. Proper torque is critical for hydraulic function. Estimated based on similar applications.
Oil Pan
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the oil pan gasket or crush washers are in good condition. Estimated value based on similar applications.
2 Transmission Oil Pan Drain Plug
M14 x 1.5
2
Transmission Oil Pan Drain Plug
M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use a new crush washer. Estimated value based on similar applications.
3 Transmission Fill Plug
M14 x 1.5
3
Transmission Fill Plug
M14 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use a new crush washer. Estimated value based on similar applications.
Shaft Housings
1 Input Shaft Housing Bolts
M8 x 1.25
1
Input Shaft Housing Bolts
M8 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 45°
Important Notes
Estimated torque value. Use a proper angle gauge.
2 Output Shaft Housing Bolts
M8 x 1.25
2
Output Shaft Housing Bolts
M8 x 1.25
Torque Specification
1. 15 ft-lbs (20 N·m)
2. 45°
Important Notes
Estimated torque value. Use a proper angle gauge.
Differential
1 Differential Housing Bolts (Internal)
M10 x 1.5
1
Differential Housing Bolts (Internal)
M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 60°
Important Notes
Estimated torque value. Proper torque is essential for gear meshing. Use a proper angle gauge.
Transfer Case
1 Transfer Case Mounting Bolts
M10 x 1.5
1
Transfer Case Mounting Bolts
M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 90°
Important Notes
Estimated value based on similar applications. Use a proper angle gauge.
Transmission Mounts
1 Transmission Mount Bolts (Body Side)
M12 x 1.75
1
Transmission Mount Bolts (Body Side)
M12 x 1.75
Torque Specification
1. 45 ft-lbs (60 N·m)
2. 90°
Important Notes
Estimated torque value. Use a proper angle gauge.
2 Transmission Mount Bolts (Transmission Side)
M12 x 1.75
2
Transmission Mount Bolts (Transmission Side)
M12 x 1.75
Torque Specification
1. 45 ft-lbs (60 N·m)
2. 90°
Important Notes
Estimated torque value. Use a proper angle gauge.
Sensors And Modules
1 Speed Sensor Bolts
M6 x 1.0
1
Speed Sensor Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten. Estimated torque based on similar sensor mountings.
2 Transmission Control Module (TCM) Mounting Bolts
M6 x 1.0
2
Transmission Control Module (TCM) Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten. Estimated based on similar modules.
Clutch Actuator
1 Clutch Actuator Mounting Bolts
M8 x 1.25
1
Clutch Actuator Mounting Bolts
M8 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Estimated torque value based on bolt size. Do not overtighten.
Oil Cooler Lines
1 Oil Cooler Line Fittings (Transmission Side)
M18 x 1.5
1
Oil Cooler Line Fittings (Transmission Side)
M18 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated torque value based on industry standards for fluid fittings. Do not overtighten.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Transmission
1 Transmission Mount Bolts (Transmission to Chassis)
M12 x 1.75
1
Transmission Mount Bolts (Transmission to Chassis)
M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the transmission to the vehicle frame/subframe. Crucial for stability, vibration damping, and maintaining driveline alignment.
2 Transmission Mount Bolts (Mount to Transmission)
M10 x 1.5
2
Transmission Mount Bolts (Mount to Transmission)
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Secures the transmission to the mount. Ensures proper support and vibration control.
3 Transmission Fluid Drain Plug
M18 x 1.5
3
Transmission Fluid Drain Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Seals the transmission fluid drain hole, preventing leaks. Typically has a crush washer. Overtightening can damage the transmission case.
4 Transmission Fill Plug
M18 x 1.5
4
Transmission Fill Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Seals the transmission fill hole. Overtightening can damage the transmission case.
5 Transmission Housing Bolts (Case Halves)
M10 x 1.5
5
Transmission Housing Bolts (Case Halves)
M10 x 1.5
Torque Specification
1. 28 ft-lbs (38 N·m)
2. 90°
Important Notes
Holds the transmission case halves together. Even and correct torque is critical for sealing and structural integrity. Sequence prevents distortion. Requires specific tightening sequence - consult factory service manual.
6 Mechatronic Unit Bolts (Transmission Control Unit)
M6 x 1.0
6
Mechatronic Unit Bolts (Transmission Control Unit)
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secure the mechatronic unit to the transmission. Proper torque ensures electrical contact and prevents damage. *Estimated value*
7 Valve Body Mounting Bolts (Within Transmission)
M6 x 1.0
7
Valve Body Mounting Bolts (Within Transmission)
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the valve body, which controls fluid flow within the transmission. Even torque is essential for proper valve operation. *Estimated value*
8 Torque Converter Bolts (to Flexplate)
M10 x 1.5
8
Torque Converter Bolts (to Flexplate)
M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Connects the torque converter to the engine's flexplate/flywheel. Crucial for transmitting engine power to the transmission.
Transfer Case
1 Transfer Case Mount Bolts (To Chassis)
M12 x 1.75
1
Transfer Case Mount Bolts (To Chassis)
M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the transfer case to the chassis. Vital for proper driveline alignment and load bearing.
2 Transfer Case Housing Bolts (Case Halves)
M10 x 1.5
2
Transfer Case Housing Bolts (Case Halves)
M10 x 1.5
Torque Specification
1. 28 ft-lbs (38 N·m)
2. 90°
Important Notes
Holds the transfer case halves together. Even and correct torque is critical for sealing and structural integrity. Sequence prevents distortion. Requires specific tightening sequence - consult factory service manual.
3 Transfer Case Input Shaft Flange Bolt/Nut
M10 x 1.5
3
Transfer Case Input Shaft Flange Bolt/Nut
M10 x 1.5
Torque Specification
1. 66 ft-lbs (90 N·m)
2. 90°
Important Notes
Fastens the input flange, transferring power into the transfer case. Proper torque is vital to prevent backlash and vibration. Verify correct value.
4 Transfer Case Output Shaft Flange Bolt/Nut
M10 x 1.5
4
Transfer Case Output Shaft Flange Bolt/Nut
M10 x 1.5
Torque Specification
1. 66 ft-lbs (90 N·m)
2. 90°
Important Notes
Fastens the output flange, transmitting power out of the transfer case. Proper torque is vital to prevent backlash and vibration. Verify correct value.
5 Transfer Case Fluid Drain Plug
M18 x 1.5
5
Transfer Case Fluid Drain Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Seals the transfer case fluid drain hole. Overtightening can damage the transfer case. Typically has a crush washer.
6 Transfer Case Fill Plug
M18 x 1.5
6
Transfer Case Fill Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Seals the transfer case fill hole. Overtightening can damage the transfer case.
Differential
1 Differential Mount Bolts (to Chassis)
M12 x 1.75
1
Differential Mount Bolts (to Chassis)
M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the differential to the vehicle frame/subframe. Vital for driveline alignment, vibration damping, and load bearing.
2 Differential Carrier Housing Bolts
M10 x 1.5
2
Differential Carrier Housing Bolts
M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 90°
Important Notes
Holds differential halves together, maintaining gear preload and alignment. Sequence is critical to avoid distortion. Requires specific tightening sequence - consult factory service manual.
3 Differential Cover Bolts
M8 x 1.25
3
Differential Cover Bolts
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the differential cover/pan to the housing. Prevents leaks.
4 Differential Input Flange Bolt/Nut
M10 x 1.5
4
Differential Input Flange Bolt/Nut
M10 x 1.5
Torque Specification
1. 66 ft-lbs (90 N·m)
2. 90°
Important Notes
Secures the input flange, transmitting power into the differential. Proper torque is vital to prevent backlash and vibration. Verify correct value.
5 Differential Output Flange Bolt/Nut
M10 x 1.5
5
Differential Output Flange Bolt/Nut
M10 x 1.5
Torque Specification
1. 66 ft-lbs (90 N·m)
2. 90°
Important Notes
Fastens the output flange, transmitting power to the drive shafts. Proper torque is vital to prevent backlash and vibration. Verify correct value.
6 Differential Fluid Drain Plug
M18 x 1.5
6
Differential Fluid Drain Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Seals the differential fluid drain hole. Usually has a crush washer.
7 Differential Fill Plug
M18 x 1.5
7
Differential Fill Plug
M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Seals the differential fill hole.
Driveshaft Axle
1 Driveshaft Center Support Bearing Bolts (if applicable)
M10 x 1.5
1
Driveshaft Center Support Bearing Bolts (if applicable)
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Secures the center support bearing of a multi-piece driveshaft to the chassis, minimizing driveshaft vibration.
2 Driveshaft Flange Bolts (to Transmission/Transfer Case/Differential)
M10 x 1.5
2
Driveshaft Flange Bolts (to Transmission/Transfer Case/Differential)
M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Connects the driveshaft to the transmission, transfer case, and differentials. Proper torque is vital for vibration-free operation and secure power transfer.
3 Axle Shaft Flange Bolts (to Differential/Wheel Hub)
M10 x 1.5
3
Axle Shaft Flange Bolts (to Differential/Wheel Hub)
M10 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
Connects the axle shaft to the differential and wheel hub, transmitting power to the wheels. Critical for secure and reliable power transfer. Verify this is the correct value.
4 Wheel Hub Nut/Bolt (Center Axle Nut)
M24 x 1.5
4
Wheel Hub Nut/Bolt (Center Axle Nut)
M24 x 1.5
Torque Specification
1. 148 ft-lbs (200 N·m)
2. 180°
Important Notes
Holds the wheel bearing and hub assembly together, retaining the axle. This is a safety-critical fastener. Often a single-use nut. Verify this is the correct value.
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Battery System
1 Battery Terminal Bolts (Main Positive & Negative)
M6 x 1.0
1
Battery Terminal Bolts (Main Positive & Negative)
M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures a secure electrical connection to the battery, critical for starting and overall system function.
2 Battery Clamp Retaining Bolts
M6 x 1.0
2
Battery Clamp Retaining Bolts
M6 x 1.0
Torque Specification
6.7 ft-lbs (9 N·m)
Important Notes
Secures the battery in its tray. Prevents movement and potential damage from vibration/impact. Estimated value based on similar applications.
Engine Electrical
1 Starter Motor Mounting Bolts
M10 x 1.5
1
Starter Motor Mounting Bolts
M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m)
2. 90°
Important Notes
Holds the starter securely to the engine block. Critical for proper engine starting and engagement.
2 Alternator Mounting Bolts
M8 x 1.25
2
Alternator Mounting Bolts
M8 x 1.25
Torque Specification
18.4 ft-lbs (25 N·m)
Important Notes
Ensures the alternator is firmly attached to the engine, allowing for belt drive and electrical generation.
3 Ground Strap Bolts (Engine to Chassis)
M8 x 1.25
3
Ground Strap Bolts (Engine to Chassis)
M8 x 1.25
Torque Specification
18.4 ft-lbs (25 N·m)
Important Notes
Provides a critical electrical ground path. Estimated value based on similar applications.
Control Modules
1 Engine Control Module (ECM/ECU) Mounting Bolts
M5 x 0.8
1
Engine Control Module (ECM/ECU) Mounting Bolts
M5 x 0.8
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Secures the ECM/ECU, preventing damage and maintaining a stable electrical connection. Tighten in a cross pattern.
2 Transmission Control Module (TCM) Mounting Bolts
M5 x 0.8
2
Transmission Control Module (TCM) Mounting Bolts
M5 x 0.8
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Securely mounts the TCM, ensuring proper operation. Estimated value based on similar applications.
3 Body Control Module (BCM) Mounting Bolts
M5 x 0.8
3
Body Control Module (BCM) Mounting Bolts
M5 x 0.8
Torque Specification
4.4 ft-lbs (6 N·m)
Important Notes
Secures the BCM, ensuring proper functionality. Estimated value based on similar applications.
Instrumentation
1 Instrument Cluster Mounting Bolts
M4 x 0.7
1
Instrument Cluster Mounting Bolts
M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Holds the cluster in place, protecting it and the connection. Estimated value based on similar applications.
Lighting
1 Headlight Assembly Mounting Bolts
M6 x 1.0
1
Headlight Assembly Mounting Bolts
M6 x 1.0
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Secures the headlight assembly, ensuring correct aiming.
2 Tail Light Assembly Mounting Bolts
M6 x 1.0
2
Tail Light Assembly Mounting Bolts
M6 x 1.0
Torque Specification
4.4 ft-lbs (6 N·m)
Important Notes
Secures the tail light assembly to the body, protecting the unit and wiring.
Sensors
1 Front Radar Sensor Mounting Bolts (Adaptive Cruise, etc.)
M6 x 1.0
1
Front Radar Sensor Mounting Bolts (Adaptive Cruise, etc.)
M6 x 1.0
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Positions and secures the radar sensor for proper operation. Critical for safety systems.
2 Rear Radar Sensor Mounting Bolts
M6 x 1.0
2
Rear Radar Sensor Mounting Bolts
M6 x 1.0
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Positions and secures the rear radar sensor for blind spot monitoring. Estimated value based on similar applications.
3 Camera Mounting Bolts (Front/Rear)
M4 x 0.7
3
Camera Mounting Bolts (Front/Rear)
M4 x 0.7
Torque Specification
3 ft-lbs (4 N·m)
Important Notes
Secures camera modules, maintaining proper aiming/alignment. Estimated value based on similar applications.
4 Steering Angle Sensor Mounting Bolts
M5 x 0.8
4
Steering Angle Sensor Mounting Bolts
M5 x 0.8
Torque Specification
4.4 ft-lbs (6 N·m)
Important Notes
Holds the steering angle sensor which is critical for ESP, Adaptive Cruise. Estimated value based on similar applications.
5 Suspension Ride Height Sensor Mounting Bolts
M6 x 1.0
5
Suspension Ride Height Sensor Mounting Bolts
M6 x 1.0
Torque Specification
5.2 ft-lbs (7 N·m)
Important Notes
Holds the sensor in place to allow the vehicle's system to monitor ride height for suspension adjustment. Estimated value based on similar applications.
Power Distribution
1 Fuse Box Mounting Bolts/Screws
M4 x 0.7
1
Fuse Box Mounting Bolts/Screws
M4 x 0.7
Torque Specification
3.7 ft-lbs (5 N·m)
Important Notes
Secures fuse boxes and their internal components. Estimated value based on similar applications.
Body Electrical
1 Window Regulator Motor Mounting Bolts
M6 x 1.0
1
Window Regulator Motor Mounting Bolts
M6 x 1.0
Torque Specification
5.9 ft-lbs (8 N·m)
Important Notes
Mounts the electric motor for the power windows. Estimated value based on similar applications.
2 Door Latch Actuator Mounting Bolts
M6 x 1.0
2
Door Latch Actuator Mounting Bolts
M6 x 1.0
Torque Specification
5.2 ft-lbs (7 N·m)
Important Notes
Secures the actuator which locks and unlocks the car door. Estimated value based on similar applications.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Exhaust Oxygen Sensors
1 Pre-Catalyst Oxygen Sensor Mounting Bolt
M8 x 1.25
1
Pre-Catalyst Oxygen Sensor Mounting Bolt
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated based on industry standards for M8 exhaust components and similar Audi applications. Ensure a leak-free seal to prevent exhaust leaks and inaccurate sensor readings.
2 Post-Catalyst Oxygen Sensor Mounting Bolt
M8 x 1.25
2
Post-Catalyst Oxygen Sensor Mounting Bolt
M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated based on industry standards for M8 exhaust components and similar Audi applications. Ensure a leak-free seal for accurate sensor readings and proper emissions system function.
Nox Egt Sensors
1 NOx Sensor Mounting Bolt
M6 x 1.0
1
NOx Sensor Mounting Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated based on similar Audi sensor mountings and industry standards for M6 bolts. Ensure proper sensor alignment and prevent damage to the sensor or its threads.
2 Exhaust Gas Temperature (EGT) Sensor Mounting Bolt
M6 x 1.0
2
Exhaust Gas Temperature (EGT) Sensor Mounting Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated based on similar Audi sensor mountings and industry standards for M6 bolts. Proper torque prevents damage, vibration, and ensures accurate sensor readings.
Dpf Pressure Sensors
1 DPF Pressure Sensor Mounting Bolt
M6 x 1.0
1
DPF Pressure Sensor Mounting Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated based on similar Audi sensor mountings and industry standards for M6 bolts. Consistent torque ensures a good seal and prevents vibrations.
2 Differential Pressure Sensor Mounting Bolt
M6 x 1.0
2
Differential Pressure Sensor Mounting Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated based on similar Audi sensor mountings and industry standards for M6 bolts. This is for a differential pressure sensor, if applicable to this Q8 model. Proper torque prevents damage and ensures reliable readings.
Intake Air Sensors
1 Intake Manifold Pressure Sensor Bolt
M5 x 0.8
1
Intake Manifold Pressure Sensor Bolt
M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated based on similar Audi sensor mountings and industry standards for M5 bolts in plastic components. Overtightening can damage the plastic sensor housing.
2 Air Mass Sensor Mounting Bolts
M5 x 0.8
2
Air Mass Sensor Mounting Bolts
M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated based on similar Audi sensor mountings and industry standards for M5 bolts in plastic components. Overtightening can strip threads in the plastic housing. Tighten evenly for accurate readings.
Electrical Connectors
1 Electrical Connector Mounting Bolts
M4 x 0.7
1
Electrical Connector Mounting Bolts
M4 x 0.7
Torque Specification
3.5 ft-lbs (5 N·m)
Important Notes
Estimated based on Audi connector mounting and industry standards for M4 screws into plastic. Proper torque ensures the connector is held securely but prevents damage to the threaded inserts.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold
1 Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
1
Exhaust Manifold to Cylinder Head Bolts
M10 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m)
2. 90°
Important Notes
These are typically torque-to-yield bolts and must be replaced. Tighten in sequence.
2 Exhaust Manifold Heat Shield Bolts
M6 x 1.0
2
Exhaust Manifold Heat Shield Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar applications.
Downpipe
1 Exhaust Manifold to Downpipe Flange Bolts/Nuts
M10 x 1.5
1
Exhaust Manifold to Downpipe Flange Bolts/Nuts
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even pressure on the gasket.
2 Downpipe Support Bracket Bolts
M10 x 1.5
2
Downpipe Support Bracket Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
None
Midpipe Catalytic Converter
1 Catalytic Converter/Midpipe to Downpipe Flange Bolts/Nuts
M10 x 1.5
1
Catalytic Converter/Midpipe to Downpipe Flange Bolts/Nuts
M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even pressure on the gasket.
2 Mid-Pipe Support Bracket Bolts
M10 x 1.5
2
Mid-Pipe Support Bracket Bolts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
None
Resonator Muffler
1 Resonator or Muffler to Midpipe Flange Bolts/Nuts
M10 x 1.5
1
Resonator or Muffler to Midpipe Flange Bolts/Nuts
M10 x 1.5
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even pressure on the gasket.
2 Muffler Hanger Bolts
M10 x 1.5
2
Muffler Hanger Bolts
M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on similar applications.
Exhaust Clamps
1 Exhaust System Clamp Bolts
M8 x 1.25
1
Exhaust System Clamp Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
None
Sensors
1 Oxygen Sensor
M18 x 1.5
1
Oxygen Sensor
M18 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
None
2 Exhaust Pressure Sensor
M8 x 1.25
2
Exhaust Pressure Sensor
M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
None
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Tank Components
1 Fuel Tank Mounting Bolts
M10 x 1.5
1
Fuel Tank Mounting Bolts
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Industry standard for similar-sized mounting bolts. Correct torque ensures the tank is firmly mounted, preventing movement and potential damage or leaks.
2 Fuel Tank Strap Bolts
M10 x 1.5
2
Fuel Tank Strap Bolts
M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Holds the fuel tank straps, securing the fuel tank to the body, preventing movement and strain on the tank. Industry standard for similar sized mounting bolts.
3 Fuel Tank Filler Neck Mounting Bolts
M6 x 1.0
3
Fuel Tank Filler Neck Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the filler neck to the fuel tank and vehicle body. Proper torque prevents leaks around the filler neck seal. Industry Standard for small flange bolts.
4 Fuel Pump Module Retaining Bolts
M6 x 1.0
4
Fuel Pump Module Retaining Bolts
M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Secures the fuel pump assembly to the tank. Prevents fuel leaks and ensures proper fuel pump sealing. Similar Audi models and industry standard for small flange bolts.
5 Fuel Level Sensor Mounting Screws
M5 x 0.8
5
Fuel Level Sensor Mounting Screws
M5 x 0.8
Torque Specification
4.5 ft-lbs (6 N·m)
Important Notes
These screws secure the fuel level sending unit. Correct torque prevents damage to the sensor or leaks. Estimated, based on similar size sensor mounting screws in Audi models.
6 Fuel Vapor Canister Mounting Bolts
M6 x 1.0
6
Fuel Vapor Canister Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the vapor canister to the body of the car. Proper torque prevents rattles and unwanted leaks. Industry standard for similar-sized mounting bolts on EVAP systems.
Fuel Lines And Rails
1 High-Pressure Fuel Pump Mounting Bolts (to Engine)
M8 x 1.25
1
High-Pressure Fuel Pump Mounting Bolts (to Engine)
M8 x 1.25
Torque Specification
1. 18 ft-lbs (25 N·m)
2. 90°
Important Notes
Secures the high-pressure fuel pump to the engine. This is a critical safety component and correct torque is necessary for proper pump function and to prevent leaks. Use proper sequence. Similar Audi engines.
2 High-Pressure Fuel Line to Pump
M14 x 1.5
2
High-Pressure Fuel Line to Pump
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures a tight, leak-free seal at the high-pressure inlet for the fuel pump. Similar Audi models.
3 High-Pressure Fuel Line to Rail
M14 x 1.5
3
High-Pressure Fuel Line to Rail
M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures a tight, leak-free seal at the high-pressure fuel rail inlet. Similar Audi models.
4 Fuel Rail Mounting Bolts
M6 x 1.0
4
Fuel Rail Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Holds the fuel rail to the intake manifold. Proper torque ensures the rail is firmly mounted and seals properly at injector locations. Industry Standard for similar sized bolts.
5 Fuel Injector Retaining Bolts/Screws
M5 x 0.8
5
Fuel Injector Retaining Bolts/Screws
M5 x 0.8
Torque Specification
4.5 ft-lbs (6 N·m)
Important Notes
Secures the fuel injectors in the fuel rail and manifold. Prevents leaks at the injector o-rings. Similar Audi models.
6 Fuel Line Bracket Mounting Bolts (various locations)
M6 x 1.0
6
Fuel Line Bracket Mounting Bolts (various locations)
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Holds the fuel lines in place, preventing rubbing and damage from vibration. Various locations under the vehicle and within the engine bay. Industry standard for small flange bolts.
7 Fuel Pressure Sensor Mounting
M6 x 1.0
7
Fuel Pressure Sensor Mounting
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Seals the fuel pressure sensor against the fuel rail, preventing leaks and maintaining accurate pressure readings. Estimated, based on similar sized sensors in other models.
8 Fuel Filter Bracket Mounting Bolts
M6 x 1.0
8
Fuel Filter Bracket Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the fuel filter and prevents vibration and leaks. Industry standard for similar sized mounting bolts.
9 Low Pressure Fuel Line Clamps (Hose Clamps)
N/A
9
Low Pressure Fuel Line Clamps (Hose Clamps)
N/A
Torque Specification
0.16 ft-lbs (2.5 N·m)
Important Notes
Secures low-pressure fuel hoses, preventing leaks and ensuring secure connections. These are hose clamps and should be tightened by hand with a driver, rather than using a torque wrench to the correct value. Industry standard for hose clamps of similar size.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Compressor System
1 Compressor Mounting Bolts
M8 x 1.25
1
Compressor Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated value based on standard M8 bolts for compressor mounts in similar Audi models. Use a star pattern when tightening.
2 Compressor Clutch Bolt/Nut
M6 x 1.0
2
Compressor Clutch Bolt/Nut
M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value based on industry standards for A/C compressor clutches. Use a holding tool to prevent the shaft from rotating during tightening.
Condenser System
1 Condenser Mounting Bolts
M6 x 1.0
1
Condenser Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on common M6 bolts used in mounting condensers. Use a star pattern to evenly distribute the load.
2 Receiver Drier/Accumulator Mounting Bolts/Strap
M6 x 1.0
2
Receiver Drier/Accumulator Mounting Bolts/Strap
M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on industry standard for 6mm fasteners for this type of component mounting.
Hvac Module
1 HVAC Module Housing Bolts
Self-Tapping Screw M5 x 0.8
1
HVAC Module Housing Bolts
Self-Tapping Screw M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value based on specifications for similar-sized self-tapping screws commonly used for plastic housing assemblies. Do not overtighten, as it may crack the plastic.
2 Evaporator Core Mounting Bolts
M6 x 1.0
2
Evaporator Core Mounting Bolts
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value based on similar sized bolts in HVAC core housings. Use a star pattern for even pressure if applicable.
3 Expansion Valve Mounting Bolts
M6 x 1.0
3
Expansion Valve Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Standard values based on M6 fasteners for this type of application. Ensure proper o-ring seating when installing.
Refrigerant Lines
1 Refrigerant Line Fittings (Aluminum)
N/A
1
Refrigerant Line Fittings (Aluminum)
N/A
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Standard value for aluminum refrigerant line fittings with O-ring or flare type connections. Always use two wrenches to prevent line damage.
2 Refrigerant Line Fittings (Steel)
N/A
2
Refrigerant Line Fittings (Steel)
N/A
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Standard value for steel refrigerant line fittings with O-ring or flare type connections. Always use two wrenches to prevent line damage.
Blower Motor
1 Blower Motor Mounting Bolts
M5 x 0.8
1
Blower Motor Mounting Bolts
M5 x 0.8
Torque Specification
4.5 ft-lbs (6 N·m)
Important Notes
Estimated value based on similar components in other Audi vehicles. Do not over tighten or crack the plastic.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Front Suspension
1 Upper Control Arm to Frame Bolts (Front)
M12 x 1.5
1
Upper Control Arm to Frame Bolts (Front)
M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
Stretch bolts, must be replaced each time they are removed. Failure to replace may lead to component failure or loss of proper alignment. These bolts secure the upper control arms to the chassis.
2 Upper Control Arm to Steering Knuckle Bolt (Front)
M12 x 1.5
2
Upper Control Arm to Steering Knuckle Bolt (Front)
M12 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 90°
Important Notes
Stretch bolt needs to be replaced each time it is removed. Secures the upper control arm to the steering knuckle.
3 Lower Control Arm to Frame Bolts (Front)
M14 x 1.5
3
Lower Control Arm to Frame Bolts (Front)
M14 x 1.5
Torque Specification
1. 52 ft-lbs (70 N·m)
2. 90°
Important Notes
Stretch bolt needs to be replaced each time it is removed. Secures the lower control arms to the chassis.
4 Lower Control Arm to Steering Knuckle Bolt (Front)
M14 x 1.5
4
Lower Control Arm to Steering Knuckle Bolt (Front)
M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m)
2. 90°
Important Notes
Stretch bolt needs to be replaced each time it is removed. Connects the lower control arm to the steering knuckle.
5 Sway Bar Link to Strut Bolt (Front)
M10 x 1.25
5
Sway Bar Link to Strut Bolt (Front)
M10 x 1.25
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 45°
Important Notes
This is a stretch bolt, connect the sway bar to the strut.
6 Sway Bar Link to Sway Bar Bolt (Front)
M8 x 1.25
6
Sway Bar Link to Sway Bar Bolt (Front)
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Connects the sway bar link to the sway bar itself.
7 Strut Assembly Upper Mount Bolts (Front)
M8 x 1.25
7
Strut Assembly Upper Mount Bolts (Front)
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the strut assembly to the vehicle's body.
8 Strut to Steering Knuckle Bolts (Front)
M14 x 1.5
8
Strut to Steering Knuckle Bolts (Front)
M14 x 1.5
Torque Specification
1. 103 ft-lbs (140 N·m)
2. 90°
Important Notes
These are stretch bolts and should be replaced every time they are removed. Fastens the strut to the steering knuckle.
9 Brake Caliper to Steering Knuckle Bolts (Front)
M14 x 1.5
9
Brake Caliper to Steering Knuckle Bolts (Front)
M14 x 1.5
Torque Specification
133 ft-lbs (180 N·m)
Important Notes
Attaches the brake caliper to the steering knuckle.
10 Wheel Speed Sensor Bolt (Front)
M6 x 1.0
10
Wheel Speed Sensor Bolt (Front)
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Securely fastens the wheel speed sensor.
11 Tie Rod End to Steering Knuckle Nut (Front)
M14 x 1.5
11
Tie Rod End to Steering Knuckle Nut (Front)
M14 x 1.5
Torque Specification
1. 37 ft-lbs (50 N·m)
2. 45°
Important Notes
This is a stretch nut and should be replaced each time it is removed. Connects the tie rod to the steering knuckle.
12 Axle Nut (Front)
M24 x 1.5
12
Axle Nut (Front)
M24 x 1.5
Torque Specification
1. 148 ft-lbs (200 N·m)
2. 180°
Important Notes
This is a stretch nut and needs to be replaced each time it's removed. Secures the drive axle to the wheel hub.
Rear Suspension
1 Upper Control Arm to Frame Bolts (Rear)
M12 x 1.5
1
Upper Control Arm to Frame Bolts (Rear)
M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
Stretch bolt needs to be replaced each time it's removed. Secures the upper control arms to the vehicle's frame.
2 Upper Control Arm to Wheel Carrier Bolt (Rear)
M12 x 1.5
2
Upper Control Arm to Wheel Carrier Bolt (Rear)
M12 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 90°
Important Notes
Stretch bolt needs to be replaced each time it's removed. Connects the upper control arm to the wheel carrier.
3 Lower Control Arm to Frame Bolts (Rear)
M14 x 1.5
3
Lower Control Arm to Frame Bolts (Rear)
M14 x 1.5
Torque Specification
1. 52 ft-lbs (70 N·m)
2. 90°
Important Notes
These are stretch bolts and need to be replaced each time they're removed. Secures the lower control arms to the chassis.
4 Lower Control Arm to Wheel Carrier Bolt (Rear)
M14 x 1.5
4
Lower Control Arm to Wheel Carrier Bolt (Rear)
M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m)
2. 90°
Important Notes
These are stretch bolts and must be replaced every time they are removed. Fastens the lower control arm to the wheel carrier.
5 Toe Link to Frame Bolt (Rear)
M12 x 1.5
5
Toe Link to Frame Bolt (Rear)
M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
These are stretch bolts and must be replaced every time they are removed. Secures the toe link to the chassis.
6 Toe Link to Wheel Carrier Bolt (Rear)
M12 x 1.5
6
Toe Link to Wheel Carrier Bolt (Rear)
M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m)
2. 90°
Important Notes
These are stretch bolts and must be replaced every time they are removed. Connects the toe link to the wheel carrier.
7 Sway Bar Link to Control Arm Bolt (Rear)
M10 x 1.25
7
Sway Bar Link to Control Arm Bolt (Rear)
M10 x 1.25
Torque Specification
1. 30 ft-lbs (40 N·m)
2. 45°
Important Notes
This is a stretch bolt. Connects the sway bar link to the control arm.
8 Sway Bar Link to Sway Bar Bolt (Rear)
M8 x 1.25
8
Sway Bar Link to Sway Bar Bolt (Rear)
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Connects the sway bar link to the sway bar itself.
9 Rear Shock Absorber Lower Mount Bolt (Rear)
M14 x 1.5
9
Rear Shock Absorber Lower Mount Bolt (Rear)
M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m)
2. 90°
Important Notes
This is a stretch bolt and needs to be replaced each time its removed. Secures the bottom of the shock absorber to the lower control arm.
10 Rear Shock Absorber Upper Mount Bolts (Rear)
M8 x 1.25
10
Rear Shock Absorber Upper Mount Bolts (Rear)
M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts attach the upper part of the shock absorber to the chassis.
11 Brake Caliper to Wheel Carrier Bolts (Rear)
M14 x 1.5
11
Brake Caliper to Wheel Carrier Bolts (Rear)
M14 x 1.5
Torque Specification
133 ft-lbs (180 N·m)
Important Notes
These bolts are used to mount the brake caliper to the wheel carrier.
12 Wheel Speed Sensor Bolt (Rear)
M6 x 1.0
12
Wheel Speed Sensor Bolt (Rear)
M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the rear wheel speed sensor.
13 Axle Nut (Rear)
M24 x 1.5
13
Axle Nut (Rear)
M24 x 1.5
Torque Specification
1. 148 ft-lbs (200 N·m)
2. 180°
Important Notes
This is a stretch nut and should be replaced each time it is removed. Secures the axle to the wheel hub.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the recommended torque for the Audi Q8 2018 lug nuts?
Q1
What IS the recommended torque for the Audi Q8 2018 lug nuts?
140 Nm (103 ft-lb) following a star pattern, as per Audi technical specifications.
Q2 What precautions should be taken while tightening suspension bolts?
Q2
What precautions should be taken while tightening suspension bolts?
Always use a torque wrench to ensure proper tension and prevent overtightening. Refer to the specific torque values for each bolt.
Q3 Can I use an impact wrench to tighten engine bolts?
Q3
Can I use an impact wrench to tighten engine bolts?
No, it IS not recommended to use an impact wrench for engine bolts. Use a torque wrench with the appropriate torque setting for these critical components.
Q4 What are the consequences of overtightening bolts?
Q4
What are the consequences of overtightening bolts?
Overtightening bolts can strip threads, damage components, or cause structural failure. Always follow the specified torque values to prevent these risks.
Q5 How often should I check torque specifications for my Audi Q8?
Q5
How often should I check torque specifications for my Audi Q8?
Torque specifications should be checked during regular maintenance intervals or after any major repairs involving the removal and reinstallation of components.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the Q8.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Front Axle Suspension Bolt Torque Specifications
Technical procedure for tightening suspension bolts on the Audi Q8.
- Tighten the upper control arm mounting bolts to 60 Nm.
- Tighten the lower control arm mounting bolts to 80 Nm.
- Tighten the tie rod end ball joints to 40 Nm.
- Tighten the stabilizer bar links to 25 Nm.
Rear Axle Suspension Bolt Torque Specifications
Technical procedure for tightening suspension bolts on the Audi Q8.
- Tighten the upper control arm mounting bolts to 60 Nm.
- Tighten the lower control arm mounting bolts to 80 Nm.
- Tighten the tie rod end ball joints to 40 Nm.
- Tighten the stabilizer bar links to 25 Nm.
Technical Service Bulletins
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.