Audi Vehicle Models Audi Q3 2018-present Torque Specifications
Audi Vehicle Models Audi Q3 2018-present

Audi Vehicle Models Audi Q3 2018-present Torque Specifications

Complete Audi Vehicle Models Audi Q3 2018-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

2.0l Engine

Torque specifications for 2.0L Engine

Engine Core

1

Cylinder Head Bolts (Initial Pass)

M12 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Initial pass ensures even seating of the cylinder head. Always use new bolts. Use a specific tightening sequence provided in the repair manual.
2

Cylinder Head Bolts (Second Pass)

M12 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Second pass applies torque angle to the cylinder head. Follow the tightening sequence. Always use new bolts.
3

Cylinder Head Bolts (Third Pass)

M12 x 1.5
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90° 3. 90°
Important Notes
Final pass applies the last 90 degrees to the cylinder head bolts. Follow the correct sequence. Always use new bolts.
4

Camshaft Bearing Cap Bolts

M8 x 1.25
Torque Specification
1. 7.4 ft-lbs (10 N·m) 2. 90°
Important Notes
Secures camshafts. Tighten evenly to avoid camshaft misalignment. Always use new bolts.
5

Connecting Rod Cap Bolts (Initial Pass)

M9 x 1.0
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
First pass for the connecting rod bolts. Always use new bolts.
6

Connecting Rod Cap Bolts (Final Pass)

M9 x 1.0
Torque Specification
1. 22 ft-lbs (30 N·m) 2. 90°
Important Notes
Final pass for the connecting rod bolts. Follow sequence. Always use new bolts.
7

Crankshaft Main Bearing Cap Bolts (Initial Pass)

M12 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
First pass for main bearing bolts. Proper torque essential for crankshaft alignment. Always use new bolts.
8

Crankshaft Main Bearing Cap Bolts (Final Pass)

M12 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Final pass to secure crankshaft bearings. Follow sequence. Always use new bolts.
9

Flywheel/Flexplate Bolts

M12 x 1.25
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 90°
Important Notes
Attaches flywheel or flexplate to crankshaft. Always use new stretch bolts.
10

Oil Pan Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the oil pan to the engine block. Tighten evenly. Estimated value based on common M6 bolts.

Engine External

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Secures the intake manifold to the cylinder head. Estimated for M8 bolts. Tighten in a crisscross pattern.
2

Exhaust Manifold Nuts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Attaches the exhaust manifold to the cylinder head. Tighten in a star pattern.
3

Turbocharger Mounting Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Holds the turbocharger. Ensure even tightening.
4

Turbocharger Oil Feed Line Bolt

M10 x 1.0 (Banjo)
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Secures the oil feed line. Use new crush washers. Estimated value for banjo bolts.
5

Turbocharger Oil Return Line Bolt

M10 x 1.0 (Banjo)
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Secures the oil return line. Use new crush washers. Estimated value for banjo bolts.
6

Water Pump Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Secures water pump. Tighten evenly.
7

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Holds thermostat housing. Estimated value for small M6 bolts. Tighten evenly.
8

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Holds alternator to engine. Estimated value for M8 bolts. Tighten evenly.
9

Starter Mounting Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Holds starter to engine. Estimated value for M10 bolts. Tighten evenly.
10

Engine Mount Bolts (Engine Side)

M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the engine to the mount. Estimated value based on typical engine mount bolts.
11

Engine Mount Bolts (Body Side)

M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the mount to the chassis. Estimated value based on typical engine mount bolts.
12

Crankshaft Pulley Bolt (Dampener)

M18 x 1.5
Torque Specification
1. 110 ft-lbs (150 N·m) 2. 180°
Important Notes
Secures crankshaft dampener. Always use a new stretch bolt. Final angle torque is critical for dampener operation.

Fuel System

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures fuel rail to the intake manifold. Estimated value for M6 bolts. Tighten evenly.
2

Fuel Injector Retaining Bolts

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Holds fuel injectors in place. Estimated value for small injector bolts. Tighten evenly.
3

High Pressure Fuel Pump Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the high pressure fuel pump. Tighten evenly.

Cooling And Lubrication

1

Oil Filter Housing Bolt

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the oil filter housing. Tighten evenly.

Sensors

1

Mass Air Flow Sensor Bolts (MAF)

M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Attaches the MAF sensor. Estimated value for small M5 bolts. Tighten evenly.

Body

Torque specifications for Body

Front Bumper

1

Front Bumper Cover Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Estimated based on similar Audi models and common plastic trim bolt size. These bolts secure the bumper cover to the structural reinforcement. Proper torque is essential to ensure secure attachment and prevent vibration or misalignment of the cover, and proper alignment for panel gaps.
2

Front Bumper Reinforcement Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
These are critical safety fasteners as they attach the energy-absorbing bumper reinforcement to the vehicle's frame. Proper torque is vital for energy management in a frontal collision.
3

Front Bumper Lower Spoiler Mounting Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Estimated, based on typical plastic trim bolt size. These screws affix the lower spoiler to the bumper cover. Torque is critical to prevent cracking of plastic components and ensure proper fit.
4

Headlight Mounting Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Industry standard for M6 fasteners on automotive lighting. These bolts hold the headlight assembly securely to the body. Proper torque prevents misalignment and ensures accurate headlight aim.

Fender

1

Fender Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Similar year Audi Q3. These bolts secure the fender to the vehicle's frame. Proper torque ensures proper fitment, panel gaps, and the structural rigidity of the body.
2

Fender Liner Mounting Screws/Clips

M5 x 0.8
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Estimated, typical plastic trim screw torque. Hand tight for clips. These fasteners hold the plastic fender liner in place. Over-tightening can damage the plastic.

Hood

1

Hood Hinge Mounting Bolts (to Hood)

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Similar year Audi Q3. These bolts attach the hood to the hinges. Correct torque ensures smooth operation and proper alignment.
2

Hood Hinge Mounting Bolts (to Body/Fender)

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Similar year Audi Q3. Secures the hood hinges to the body for proper hood alignment and safe hinge function.
3

Hood Latch Mounting Bolts (to Hood)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated, based on similar Audi models and applications. These bolts hold the hood latch mechanism in place. Correct torque ensures reliable latching.
4

Hood Strut Mounting Bolt (to Hood and Body)

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated, based on similar strut applications. Secures the gas strut that supports the hood and is important for proper opening and closing.

Door

1

Door Hinge Mounting Bolts (to Door)

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Similar model Audi vehicle. Secures the door to the hinges. Proper torque is necessary for safe door operation and alignment.
2

Door Hinge Mounting Bolts (to Body/Pillar)

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Similar model Audi vehicle. Secures the door hinges to the car's frame for safe and reliable door operation.
3

Door Latch/Striker Mounting Bolts (to Door)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Similar model Audi vehicle. These bolts secure the door latch. Correct torque ensures the latch engages correctly.
4

Door Latch/Striker Mounting Bolts (to Body/Pillar)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Similar model Audi vehicle. These bolts secure the door striker. Correct torque is critical for reliable door closure and safety. The striker position will also influence panel alignment.
5

Door Handle Mounting Screws

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated, based on typical door handle fastener size. These screws secure the door handle. Proper torque is essential for a secure and functional handle.
6

Door Panel Mounting Screws/Clips

M4 x 0.7
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Estimated based on interior trim fastener application. Secures the interior door panel and prevents rattling or loose panels. Hand tight for clips.

Tailgate

1

Tailgate Hinge Mounting Bolts (to Tailgate)

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Similar model Audi vehicle. These bolts attach the tailgate to the hinges. Correct torque ensures smooth operation and proper alignment.
2

Tailgate Hinge Mounting Bolts (to Body)

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Similar model Audi vehicle. Secures the tailgate hinges to the body of the vehicle for reliable and safe operation.
3

Tailgate Latch Mounting Bolts (to Tailgate)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Similar model Audi vehicle. These bolts secure the tailgate latch. Correct torque ensures secure and reliable latching.
4

Tailgate Latch Striker Mounting Bolts (to Body)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Similar model Audi vehicle. Secures the tailgate striker on the body, necessary for proper closure. The striker position can also influence panel alignment.
5

Tailgate Strut Mounting Bolt (to Tailgate and Body)

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated, based on similar strut applications. Secures the gas struts that support the tailgate and is important for proper opening and closing.

Side Mirrors

1

Side Mirror Mounting Bolts (to Door)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated, based on industry standard for small mirror mount bolts. Secure the side mirror assembly to the door. Proper torque prevents vibration and ensures a firm mounting.

Roof

1

Roof Rail Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Estimated based on similar applications and small M6 fasteners. Attaches the roof rails to the vehicle's roof structure and provides secure attachment for cargo accessories.

Trim

1

Body Side Moulding Screws/Clips

M4 x 0.7
Torque Specification
2 ft-lbs (3 N·m)
Important Notes
Estimated. Hand tight for clips. Secure the body side moldings or trim pieces.

Brakes

Torque specifications for Brakes

Front Calipers

1

Front Caliper Guide Pin Bolts

M8 x 1.25
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Ensures proper caliper sliding action for even brake pad wear.
2

Front Caliper Mounting Bracket Bolts

M14 x 1.5
Torque Specification
1. 89 ft-lbs (120 N·m) 2. 90°
Important Notes
These bolts are safety critical and often require replacement after removal. Final torque is achieved via angle specification. Ensure bolts are tightened evenly to avoid stress on the caliper bracket.
3

Front Brake Hose to Caliper Bolt

M10 x 1.0 (Banjo)
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new copper sealing washers. Over-tightening can damage the banjo fitting.
4

Front Brake Caliper Bleeder Screw

M7 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Avoid over-tightening to prevent damage to the caliper threads. Torque value is an estimate based on similar bleeder screws.

Rear Calipers

1

Rear Caliper Guide Pin Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensures proper caliper sliding action for even brake pad wear.
2

Rear Caliper Mounting Bracket Bolts

M12 x 1.5
Torque Specification
1. 59 ft-lbs (80 N·m) 2. 90°
Important Notes
These bolts are safety critical and often require replacement after removal. Final torque is achieved via angle specification. Ensure bolts are tightened evenly to avoid stress on the caliper bracket.
3

Rear Brake Hose to Caliper Bolt

M10 x 1.0 (Banjo)
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use new copper sealing washers. Over-tightening can damage the banjo fitting.
4

Rear Brake Caliper Bleeder Screw

M7 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Avoid over-tightening to prevent damage to the caliper threads. Torque value is an estimate based on similar bleeder screws.

Rotors

1

Front Brake Disc Rotor Retaining Screw

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
This screw holds the rotor in place during wheel installation; it is not load-bearing. Value is estimated.
2

Rear Brake Disc Rotor Retaining Screw

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
This screw holds the rotor in place during wheel installation; it is not load-bearing. Value is estimated.

Epb

1

Electronic Parking Brake (EPB) Motor Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensures the EPB motor is securely mounted to the caliper. Value is estimated.

Abs

1

ABS Sensor Mounting Bolt

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Do not over-tighten; can damage the sensor. Torque value is an estimate.
2

ABS Hydraulic Module Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensures the ABS module is securely mounted.

Master Cylinder Booster

1

Brake Master Cylinder Mounting Nuts/Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures master cylinder to the booster; proper torque ensures safe brake operation.
2

Brake Booster Mounting Nuts/Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures brake booster to the firewall; maintains vacuum assist during braking.

Brake Lines

1

Brake Line Fittings (Hard Lines)

Varies (typically M10 x 1.0)
Torque Specification
12 ft-lbs (17 N·m)
Important Notes
Ensures a leak free connection. Torque value is an average value for standard brake line fittings, final value can depend on the fitting type used. Torque value is estimated.

Wheel Speed Sensors

1

Wheel Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not over-tighten; can damage the sensor. Torque value is an estimate.

Dq250 Transmission

Torque specifications for Dq250 Transmission

Transmission Mounting

1

Engine to Transmission Bolts

M12 x 1.5
Torque Specification
1. 44 ft-lbs (60 N·m) 2. 90°
Important Notes
These bolts secure the transmission housing to the engine block. Correct torque is critical for proper alignment and preventing vibration. Use new bolts. Angle-tightening achieves proper clamping force.
2

Transmission Mount Bracket to Chassis Bolts

M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
These bolts connect the transmission mount bracket to the chassis. Proper torque is critical for preventing excessive vibration. Use new bolts. Angle-tightening achieves proper clamping force.
3

Transmission to Mount Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
These bolts connect the transmission housing to the mount. Ensuring proper torque is crucial for vibration damping and maintaining drivetrain alignment.

Mechatronic Unit

1

Mechatronic Unit Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts secure the mechatronic unit to the transmission housing. Over-tightening can damage the sensitive electronics and valve body. Estimated value based on similar components and bolt size. Use a crisscross pattern for even tightening.

Oil Pan

1

Oil Pan Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts secure the transmission oil pan to the transmission housing. Consistent torque is essential for creating a leak-free seal. Typical for similar aluminum housings with gaskets. Use a crisscross pattern for even tightening.

Differential Housing

1

Differential Housing Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
If the differential has its own housing bolted to the transmission, this torque is critical for correct alignment and gear meshing, as well as preventing leaks. Estimated based on similar applications. Use a crisscross pattern for even tightening.

Plugs

1

Fill Plug

M24 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Correct torque on the fill plug ensures a tight seal and prevents fluid leakage. Use a new sealing washer.
2

Drain Plug

M24 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Correct torque on the drain plug ensures a tight seal and prevents fluid leakage. Use a new sealing washer.

Sensors

1

Input Shaft Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the sensor which is crucial for proper transmission operation. Over-tightening could damage sensor or housing. Estimated based on similar sensor mountings.
2

Output Shaft Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the sensor which is crucial for proper transmission operation. Over-tightening could damage sensor or housing. Estimated based on similar sensor mountings.

Clutch Actuator

1

Clutch Actuator Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
These bolts secure the clutch actuator to the transmission. Proper torque is necessary for accurate clutch operation. Estimated based on small bolting applications.

Line Brackets

1

Coolant/Oil Line Bracket Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
These bolts secure brackets holding transmission oil or coolant lines to the transmission housing or engine. Prevents line movement and potential leaks. Estimated based on medium sized bracket bolts.

Drive Flanges

1

Drive Flange Bolts

M10 x 1.5
Torque Specification
1. 59 ft-lbs (80 N·m) 2. 90°
Important Notes
These bolts secure the drive flanges to the output shafts. This is a critical joint for power transfer, requiring specific torque and angle for safety and longevity. These are usually single-use stretch bolts. Always replace these bolts with new ones.

Drivetrain

Torque specifications for Drivetrain

Transmission Transaxle

1

Transmission Mount Bolts (Engine Side)

M12 x 1.75
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Secures the transmission to the engine block. Proper torque is crucial for vibration damping and preventing misalignment.
2

Transmission Mount Bolts (Chassis Side)

M12 x 1.75
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Secures the transmission to the chassis. The additional angle turn ensures proper preload of the mounting bushings.
3

Transmission Case Bolts (General)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts hold the transmission case together. Torque evenly in a star pattern to ensure proper sealing and prevent leaks. Estimated value for M8 bolts.
4

Transmission Oil Drain Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the drain plug and prevents oil leaks. Use new washer when possible.
5

Transmission Oil Fill Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the fill plug and prevents oil leaks. Use new washer when possible.
6

Mechatronics Unit Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the sensitive Mechatronics Unit within the transmission. Low torque is crucial to prevent damage.
7

Dual Clutch Unit Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures the dual clutch system within the transmission. A specific torque ensures accurate clutch operation and prevents damage.

Transfer Case

1

Transfer Case Mount Bolts

M12 x 1.75
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Secures the transfer case to the transmission or chassis. Proper torque is important for alignment. An additional angle turn ensures proper pre-load of mounting bushings.
2

Transfer Case Housing Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts hold the transfer case housing together. Torque evenly to ensure proper sealing and prevent leaks. Estimated value for M8 bolts.
3

Transfer Case Drain Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the drain plug and prevents fluid leaks. Use new washer when possible.
4

Transfer Case Fill Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the fill plug and prevents fluid leaks. Use new washer when possible.

Driveshafts Axles

1

Front Axle Shaft to Transmission Flange Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
These bolts secure the driveshaft to the transmission output flange, ensuring proper power transfer. Important for safety and proper operation.
2

Rear Axle Shaft to Differential Flange Bolts

M10 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
These bolts connect the driveshaft to the rear differential flange, crucial for power transfer to rear wheels in all-wheel-drive.
3

Front Axle Shaft CV Joint Bolts (Wheel Side)

M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Secures the driveshaft to the wheel hub. The extra turn is for proper bearing pre-load.
4

Rear Axle Shaft CV Joint Bolts (Wheel Side)

M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Connects the rear driveshaft to the wheel hub and provides proper bearing preload.
5

Center Driveshaft Support Bearing Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Supports the center driveshaft. Proper torque prevents vibration and ensures proper alignment.

Differential

1

Differential Mounting Bolts

M12 x 1.75
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Secures the differential to the chassis. Important for maintaining proper alignment and preventing excessive vibrations. Angle turn for bearing pre-load
2

Differential Housing Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
These bolts hold the differential housing together. Correct torque prevents leaks and maintains proper internal clearances. Estimated value for M8 bolts.
3

Differential Oil Drain Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the drain plug and prevents oil leaks. Use new washer when possible.
4

Differential Oil Fill Plug

M18 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Secures the fill plug and prevents oil leaks. Use new washer when possible.
5

Differential Ring Gear Bolts

M12 x 1.75
Torque Specification
1. 70 ft-lbs (95 N·m) 2. 90°
Important Notes
These bolts secure the ring gear to the differential case, which transmits the power. Critically important to tighten correctly to prevent gear failure, noise, and backlash issues. Always replace these bolts with new ones.

Haldex Coupling

1

Haldex Coupling Mounting Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Secures the Haldex coupling to the differential assembly. Proper torque is crucial to ensure the AWD system operates correctly.
2

Haldex Coupling Pump Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the Haldex pump. Low torque is important to prevent over-tightening. Ensure all bolts are torqued evenly
3

Haldex Coupling Filter Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the filter to the Haldex coupling. Low torque is essential for proper sealing without stripping threads. Ensure all bolts are torqued evenly

Electrical

Torque specifications for Electrical

Battery System

1

Battery Terminal Clamp Nut (Positive & Negative)

M8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures battery cables to battery posts. Ensure clean connections.
2

Battery Hold-Down Bolt/Clamp

M6
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures the battery within the tray. Prevents battery movement.

Charging System

1

Alternator Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secures alternator to engine block/bracket. Ensure correct belt alignment.
2

Alternator B+ Terminal Nut

M6
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures main power wire to alternator. Crucial for preventing overheating.

Starting System

1

Starter Mounting Bolts

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Securely mounts starter motor to engine. Ensure proper alignment.
2

Starter B+ Terminal Nut

M8
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures power cable to starter solenoid. Essential for reliable starting.
3

Starter Solenoid Signal Wire Terminal Nut

M5
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Connects signal wire from ignition switch. Low torque, do not overtighten.

Engine Management

1

ECU Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the ECU housing. Prevents vibration and physical damage.
2

ECU Connector Securing Screws/Bolts

M4 x 0.7
Torque Specification
1.5 ft-lbs (2 N·m)
Important Notes
Secures wiring harness connectors to ECU. Prevents accidental disconnection. Estimated value.
3

Camshaft/Crankshaft Sensor Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures the sensors to their housings. Proper positioning is critical. Estimated value.

Fuse Panel

1

Fuse Box/Panel Mounting Bolts/Screws

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Holds the fuse box securely in place. Prevents movement and ensures reliable connections. Estimated value.

Ground Points

1

Ground Terminal Bolts/Screws (M6)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Provides a solid return path for electrical circuits. Clean the contact area before installation. Use for M6 bolt sizes.
2

Ground Terminal Bolts/Screws (M8)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Provides a solid return path for electrical circuits. Clean the contact area before installation. Use for M8 bolt sizes.

Lighting

1

Headlight Mounting Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures the headlight assembly to the vehicle body. Prevents vibration.
2

Taillight Mounting Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures the taillight assembly to the vehicle body. Prevents vibration.

Sensors

1

Wheel Speed Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures wheel speed sensor to the hub. Crucial for accurate readings.

Wiring

1

Connector Retaining Screws/Clips

N/A
Torque Specification
1.5 ft-lbs (2 N·m)
Important Notes
Secures wiring harness connectors. Hand-tight with slight additional force. Estimated value. Do not overtighten.

Interior Electronics

1

Door Control Module Mounting Bolts/Screws

M5 x 0.8
Torque Specification
4 ft-lbs (5 N·m)
Important Notes
Secures control modules within door panel. Prevents rattling. Estimated value.
2

Instrument Cluster Mounting Screws

M4 x 0.7
Torque Specification
1.5 ft-lbs (2 N·m)
Important Notes
Holds the instrument cluster securely to the dashboard. Low torque, avoid damage to housing. Estimated value.

Airbag System

1

Airbag Module Mounting Bolts

M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Securely mounts airbag modules. **CRITICAL SAFETY COMPONENT**. Always confirm with vehicle-specific repair documentation and torque procedures. This is a general estimated value. Confirm specific location torques in the factory service manual.

Emissions Sensors

Torque specifications for Emissions_sensors

Exhaust Oxygen Sensors

1

Pre-Catalyst Oxygen Sensor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Apply anti-seize compound to bolt threads if appropriate for the material. Tighten to specified torque. Estimated bolt size and thread pitch.
2

Post-Catalyst Oxygen Sensor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Apply anti-seize compound to bolt threads if appropriate for the material. Tighten to specified torque. Estimated bolt size and thread pitch.

Nox Sensors

1

NOx Sensor Mounting Bolts

M6 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Apply anti-seize compound to bolt threads if appropriate for the material. Tighten to specified torque. Estimated bolt size and thread pitch.

Exhaust Gas Temperature Sensors

1

EGT Sensor Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Apply anti-seize compound to bolt threads if appropriate for the material. Tighten to specified torque. Estimated bolt size and thread pitch.

Selective Catalytic Reduction Sensors

1

SCR System Temperature Sensor Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Apply anti-seize compound to bolt threads if appropriate for the material. Tighten to specified torque. Estimated bolt size and thread pitch.

Particulate Matter Sensors

1

Particulate Matter Sensor (PMS) Mounting Bolts

M5 x 0.8
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Apply anti-seize compound to bolt threads if appropriate for the material. Tighten to specified torque. Estimated bolt size and thread pitch.

Diesel Exhaust Fluid Injector

1

DEF/AdBlue Injector Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Tighten to specified torque to avoid damage. Estimated bolt size and thread pitch.

Wiring Harness Brackets

1

Wiring Harness Bracket Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Tighten to specified torque. Estimated bolt size and thread pitch.

Manifold Pressure Sensors

1

Manifold Pressure Sensor Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure bolts and threaded holes are clean. Tighten to specified torque. Estimated bolt size and thread pitch.

Exhaust

Torque specifications for Exhaust

Turbo Downpipe

1

Turbocharger to Downpipe Flange Bolts

M10 x 1.5
Torque Specification
1. 30 ft-lbs (40 N·m) 2. 90°
Important Notes
Critical safety fastener. Torque in stages following a cross pattern.
2

Downpipe Section Flange Bolts

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure even tightening to prevent leaks.
3

Downpipe to Exhaust System Clamp Bolt

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Critical safety fastener. Ensure proper clamp alignment before tightening. Estimated value.

Exhaust Manifold

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
1. 18 ft-lbs (25 N·m) 2. 90°
Important Notes
Critical safety fastener. Tighten in a specific sequence, starting from the center and working outwards.

Exhaust Supports

1

Exhaust Support Bracket Bolts (Body/Frame)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment before tightening.
2

Rear Muffler Bracket Bolts (Body)

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper muffler alignment before tightening.
3

Exhaust Hanger Bolts (Rubber Mounts)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Do not overtighten, as this can damage the rubber mounts. Estimated value.

Exhaust Sections

1

Exhaust System Flange Bolts (Center Pipe to Muffler)

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure proper alignment of flanges before tightening.

Sensors And Shields

1

Oxygen Sensor (O2 Sensor) Mounting Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure sensor is correctly seated before tightening. Estimated Value.
2

Exhaust Gas Temperature (EGT) Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure sensor is correctly seated before tightening. Estimated Value.
3

Heat Shield Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten, this can cause damage. Estimated value.

Fuel

Torque specifications for Fuel

Fuel Pump Module

1

Fuel Pump Module Access Cover Bolts

M6
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Ensures a fuel-tight seal. Sourced from similar Audi models.
2

Fuel Pump Mounting Bolts (In-Tank)

M6
Torque Specification
8.9 ft-lbs (12 N·m)
Important Notes
Secure mounting, prevents vibration. Estimated based on similar VW/Audi configurations.

Fuel Filter

1

Fuel Filter Mounting Bracket Bolts

M6
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures bracket, prevents movement. Estimated based on industry standards.

High Pressure Fuel Pump

1

High-Pressure Fuel Pump Mounting Bolts (Engine Mounted)

M8
Torque Specification
1. 18.4 ft-lbs (25 N·m) 2. 90°
Important Notes
Critical torque plus angle. Sourced from similar Audi models.
2

High-Pressure Fuel Line Banjo Bolt (Pump End)

M12 x 1.5
Torque Specification
25.8 ft-lbs (35 N·m)
Important Notes
Secures fuel line to pump. Estimated industry standard for M12 banjo bolt.
3

High-Pressure Fuel Line Banjo Bolt (Fuel Rail End)

M12 x 1.5
Torque Specification
25.8 ft-lbs (35 N·m)
Important Notes
Secures fuel line to rail. Estimated industry standard for M12 banjo bolt.

Fuel Rail

1

Fuel Rail Mounting Bolts

M6
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures fuel rail to intake. Sourced from similar Audi models.
2

Fuel Injector Mounting Bolts

M6
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures injectors in place. Estimated based on similar injector mountings.
3

Fuel Pressure Sensor Bolts

M5
Torque Specification
5.2 ft-lbs (7 N·m)
Important Notes
Holds the fuel pressure sensor securely. Estimated based on similar sensor mounting.

Fuel Tank

1

Fuel Tank Filler Neck Bolts

M8
Torque Specification
11.1 ft-lbs (15 N·m)
Important Notes
Attaches the filler neck to the body. Estimated industry standard.
2

Fuel Tank Straps Bolts

M10
Torque Specification
18.4 ft-lbs (25 N·m)
Important Notes
Holds tank to chassis. Estimated derived from similar VW/Audi.
3

Charcoal Canister Mounting Bolts

M6
Torque Specification
7.4 ft-lbs (10 N·m)
Important Notes
Secures the charcoal canister. Estimated based on general mounting bolt torque.
4

Fuel Tank Vent Valve Mounting Bolts

M6
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures the vent valve. Estimated based on valve mounting.

Hvac

Torque specifications for Hvac

Compressor Subsystem

1

Compressor Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Secure the compressor to the engine block or mounting bracket. Use a crisscross pattern when tightening. These are critical for proper compressor operation.
2

Compressor Clutch Bolt

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Secures the clutch to the compressor shaft. Estimated thread pitch, standard may vary. Proper torque is important for clutch engagement.

Condenser Subsystem

1

Condenser Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Attaches the condenser to the vehicle frame or radiator support. Ensure proper alignment for optimal airflow.
2

A/C Line Flange Bolts (Condenser Connection)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Connects A/C lines to the condenser. Use new O-rings or seals and lubricate them with refrigerant oil. Use a crisscross tightening pattern.

Evaporator Subsystem

1

Evaporator Housing Bolts (general)

M5 x 0.8
Torque Specification
4.5 ft-lbs (6 N·m)
Important Notes
Holds the evaporator housing together. Overtightening could crack the plastic housing. These are low torque fasteners.
2

Expansion Valve Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the expansion valve to the evaporator. Use new O-rings or seals if applicable. Ensure leak-free seal.

Receiver Drier Subsystem

1

Receiver Drier Mounting Bolt(s)

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Attaches the receiver drier to the vehicle frame. Proper torque prevents vibration.

Ac Line Connections

1

A/C Line Flange Bolts (Compressor Connection)

M8 x 1.25
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Connects A/C lines to the compressor. Use new O-rings or seals and lubricate with refrigerant oil. Crisscross tightening pattern.

Blower Motor Subsystem

1

Blower Motor Mounting Bolts

M5 x 0.8
Torque Specification
4.5 ft-lbs (6 N·m)
Important Notes
Secures the blower motor to its housing. These are typically low torque fasteners.

Control Module Subsystem

1

HVAC Control Module Mounting Screws/Bolts

M4 x 0.7
Torque Specification
2.5 ft-lbs (3.4 N·m)
Important Notes
Attaches the control module to the dashboard or console. Low-torque fasteners. Overtightening could cause damage.
2

Blend Door Actuator Mounting Screws

M4 x 0.7
Torque Specification
2.5 ft-lbs (3.4 N·m)
Important Notes
Secures the blend door actuators to the HVAC housing. Low torque to prevent actuator failure.

Sensor Subsystem

1

Temperature Sensor Mounting Screws

M3 x 0.5
Torque Specification
1.7 ft-lbs (2.3 N·m)
Important Notes
Attaches temperature sensors to HVAC components. Very low torque; screws directly into plastic.
2

Refrigerant Pressure Sensor Mounting

M5 x 0.8
Torque Specification
4.5 ft-lbs (6 N·m)
Important Notes
Secures the refrigerant pressure sensor to the A/C line. Ensure a proper seal.

Suspension

Torque specifications for Suspension

Front Suspension

1

Upper Control Arm to Strut Bolts

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Estimated value based on similar Audi/VW models using M12 bolts in this application. Correct torque maintains suspension geometry and prevents play.
2

Lower Control Arm to Subframe Bolts

M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Estimated value based on similar Audi/VW models using M14 bolts in this application. These are torque-to-yield bolts and must be replaced after removal. Final angle is critical for proper clamping force.
3

Lower Control Arm Ball Joint to Steering Knuckle Bolt

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Estimated value based on similar Audi/VW models using M12 bolts in this application. Correct torque is critical for steering integrity.
4

Sway Bar Link to Strut Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on common M10 applications in sway bar links.
5

Sway Bar Link to Sway Bar Nut

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on common M8/M10 nut applications in sway bar links.
6

Strut Mount to Body Bolts

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on common M8/M10 applications in strut mounts.
7

Strut to Steering Knuckle Bolts

M14 x 1.5
Torque Specification
1. 66 ft-lbs (90 N·m) 2. 90°
Important Notes
Estimated value based on similar Audi/VW models using M14 bolts in this application. These are torque-to-yield bolts and must be replaced after removal. Final angle is critical for proper clamping force.
8

Brake Caliper Bracket Bolts

M14 x 1.5
Torque Specification
140 ft-lbs (190 N·m)
Important Notes
Critical for brake system safety. Ensure proper torque to maintain brake performance and safety.

Rear Suspension

1

Upper Control Arm to Body Bolts

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Estimated value based on similar Audi/VW models using M12 bolts in this application. Critical for rear suspension geometry.
2

Upper Control Arm to Wheel Carrier (Upright) Bolt

M12 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Estimated value based on similar Audi/VW models using M12/M14 bolts in this application. This is a torque-to-yield bolt and must be replaced after removal. Final angle is critical for proper clamping force.
3

Lower Control Arm to Body Bolts

M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Estimated value based on similar Audi/VW models using M14 bolts in this application. These are torque-to-yield bolts and must be replaced after removal. Final angle is critical for proper clamping force.
4

Lower Control Arm to Wheel Carrier (Upright) Bolt

M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 90°
Important Notes
Estimated value based on similar Audi/VW models using M14 bolts in this application. This is a torque-to-yield bolt and must be replaced after removal. Final angle is critical for proper clamping force.
5

Toe Link to Body Bolt

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Estimated value based on common M12 applications in toe links. Correct torque is vital for proper alignment and tire wear.
6

Toe Link to Wheel Carrier (Upright) Bolt

M12 x 1.5
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Estimated value based on common M12 applications in toe links. Correct torque is vital for proper alignment and tire wear.
7

Rear Sway Bar Link to Control Arm Bolt

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on common M10 applications in sway bar links.
8

Rear Sway Bar Link to Sway Bar Nut

M10 x 1.5
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated value based on common M8/M10 nut applications in sway bar links.
9

Shock Absorber Lower Mounting Bolt

M12 x 1.5
Torque Specification
52 ft-lbs (70 N·m)
Important Notes
Estimated value based on similar Audi/VW models using M12 bolts in this application. Critical for suspension damping.
10

Shock Absorber Upper Mounting Bolt/Nut

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value based on common M10 applications in shock absorber mounts.
11

Wheel Carrier to Body Bolt

M12 x 1.5
Torque Specification
1. 59 ft-lbs (80 N·m) 2. 90°
Important Notes
Estimated value based on similar Audi/VW models using M12/M14 bolts in this application. This is a torque-to-yield bolt and must be replaced after removal. Final angle is critical for proper clamping force.
12

Brake Caliper Bracket Bolts

M14 x 1.5
Torque Specification
140 ft-lbs (190 N·m)
Important Notes
Critical for brake system safety. Ensure proper torque to maintain brake performance and safety.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque for the lug nuts on a 2022 Audi Q3?

118 ft-lbs (160 Nm).

Q2

What IS the torque specification for the oil drain plug on a 2020 Audi Q3?

25 ft-lbs (34 Nm).

Q3

Can I use an impact wrench to tighten bolts on my 2018 Audi Q3?

No, using an impact wrench can over-tighten bolts and cause damage. Always use a torque wrench to ensure proper tightening.

Q4

What IS the torque specification for the spark plugs on a 2021 Audi Q3?

18 ft-lbs (24 Nm).

Q5

How often should I torque my wheel lug nuts?

As a general rule, wheel lug nuts should be torqued every 6 months or 6,000 miles, whichever comes first.

Q6

What IS the torque specification for the camshaft bolts on a 2019 Audi Q3?

74 ft-lbs (100 Nm).

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the Q3.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Tightening Wheel Lug Nuts

Ensure proper tightening of wheel lug nuts to specified torque values for optimal safety and performance.

  • Clean wheel lug nut threads and mating surfaces.
  • Apply a small amount of anti-seize lubricant to the threads.
  • Install the wheel lug nuts onto the wheel studs, hand-tightening as much as possible.
  • Use a digital torque wrench to tighten the lug nuts to the specified torque of 120 Nm (89 ft-lbs).
  • Tighten the lug nuts in a star pattern to ensure even distribution of force.
  • Re-check the tightness of the lug nuts after 50-100 miles of driving.
View full procedure

Replacing Engine Oil Drain Plug

Follow this procedure to properly replace the engine oil drain plug, ensuring a secure seal and preventing oil leaks.

  • Gather necessary tools and materials: new drain plug, crush washer, oil pan.
  • Locate the oil drain plug at the bottom of the oil pan.
  • Place the oil pan under the drain plug to catch the draining oil.
  • Use a wrench to loosen the drain plug.
  • Replace the crush washer on the drain plug with a new one.
  • Hand-tighten the drain plug back into the oil pan.
  • Use a torque wrench to tighten the drain plug to the specified torque of 30 Nm (22 ft-lbs).
  • Clean up any spilled oil and dispose of it properly.
View full procedure
Technical Service Bulletins

TSB: Incorrect Torque Values for Control Arm Bolts

2020-03-15

This bulletin addresses an error in the torque specifications for the control arm bolts on certain 2018-2020 Q3 models.

2018-2020 Q3

Resolution: The correct torque values for the control arm bolts are as follows: - Upper control arm bolts: 100 Nm (74 ft-lbs) - Lower control arm bolts: 120 Nm (89 ft-lbs)

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Audi Specs. All rights reserved.

Privacy Policy Terms of Service