Audi Vehicle Models Audi A6 2018-present Torque Specifications
Audi Vehicle Models Audi A6 2018-present

Audi Vehicle Models Audi A6 2018-present Torque Specifications

Complete Audi Vehicle Models Audi A6 2018-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

2.0l Engine

Torque specifications for 2.0L Engine

Cylinder Head and Valvetrain

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Valve Cover Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
3

Rocker Arms/Shafts Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Engine Block and Crankcase

1

Main Bearing Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
2

Connecting Rod Nuts

M12 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
3

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 1.5
Torque Specification
103 ft-lbs (140 N·m)

Timing System

1

Timing Belt/Chain Tensioner Bolt

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Camshaft Sprocket Bolt

M14 x 1.5
Torque Specification
63 ft-lbs (85 N·m)

Accessory Components

1

Water Pump Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
2

Fuel Rail Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)

Engine Mounts and Transmission

1

Engine Mounting Bolts

M12 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
2

Engine Block to Transmission Bellhousing Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N·m)

Intake and Exhaust System

1

Intake Manifold Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
2

Exhaust Manifold/Headers Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Miscellaneous

1

Spark Plugs

14mm x 1.25
Torque Specification
15 ft-lbs (20 N·m)
2

Oil Filter Cap

N/A
Torque Specification
Hand tight ft-lbs (Hand tight N·m)
Important Notes
Estimated value, consult factory manual for specific instructions.

3.0l Engine

Torque specifications for 3.0L Engine

Cylinder Head and Valve Train

1

Cylinder Head Bolts

M12 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Valve Cover Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
3

Rocker Arms/Shafts Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)

Engine Block and Main Bearings

1

Main Bearing Bolts

M14 x 2.0
Torque Specification
30 ft-lbs (40 N·m)
2

Engine Block to Transmission Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on general engine design.
3

Engine Block to Engine Mounting Bolts

M12 x 1.75
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated value based on general engine design.

Crankshaft and Connecting Rods

1

Connecting Rod Nuts

M12 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
2

Crankshaft Pulley/Harmonic Balancer Bolt

M16 x 2.0
Torque Specification
103 ft-lbs (140 N·m)

Timing System

1

Timing Belt/Chain Tensioner Bolt

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
2

Camshaft Sprocket Bolt

M14 x 2.0
Torque Specification
63 ft-lbs (85 N·m)

Intake and Exhaust Systems

1

Intake Manifold Bolts

M10 x 1.5
Torque Specification
15 ft-lbs (20 N·m)
2

Exhaust Manifold/Headers Bolts

M12 x 1.75
Torque Specification
18 ft-lbs (25 N·m)

Fuel System

1

Fuel Rail Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
2

Fuel Injector Bolts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)

Ignition System

1

Ignition Coil Bolt

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
2

Spark Plugs

M14 x 1.25
Torque Specification
15 ft-lbs (20 N·m)

Cooling System

1

Water Pump Bolts

M10 x 1.5
Torque Specification
7 ft-lbs (10 N·m)
2

Water Pump Pulley Bolts

M10 x 1.5
Torque Specification
7 ft-lbs (10 N·m)

Oil System

1

Oil Pan Bolts

M10 x 1.5
Torque Specification
84 in-lbs (10 N·m)
Important Notes
Note: The torque value is in inch-lbs, not ft-lbs.
2

Oil Drain Plug Bolt

M12 x 1.75
Torque Specification
22 ft-lbs (30 N·m)

Body

Torque specifications for Body

Body Fuel System

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure straps are properly aligned before tightening. Apply torque evenly to both sides.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure a proper seal between filler neck and body. Do not over-tighten.

Body Exterior

1

Door Hinge Bolts to Body

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated torque value. Ensure door alignment during tightening. Use correct bolt grade.
2

Hood Hinge Bolts to Body

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated torque value. Ensure hood alignment during tightening. Use correct bolt grade.
3

Fender Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated torque value. Confirm specific spec. Tighten using a cross pattern.
4

Bumper Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated torque value, confirm specific spec. Check for proper bumper alignment before tightening.
5

Tail Light Mounting Bolts

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated torque value. Ensure proper tail light alignment before tightening. Do not over-tighten.
6

Rear Quarter Panel Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated torque value. Confirm specific spec. Tighten using a cross pattern.
7

Roof Mounting Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated torque value. Tighten in a progressive pattern to ensure even pressure. Confirm specific spec.

Body Interior

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated torque value, confirm specific spec. Ensure proper seat alignment.
2

Seat Belt Mounting Bolts to Body

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Estimated torque for M10 bolts. Smaller bolts use 18 ft-lbs (25 N·m). Confirm specific spec. Critical for safety.
3

Body Control Module (BCM) Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated torque value, confirm specific spec. Ensure proper BCM mounting.

Body Chassis

1

Radiator Support/Core Support Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Estimated torque value, confirm specific spec. Ensure proper alignment.
2

Wheel Lug Nuts

M14 x 1.5
Torque Specification
103 ft-lbs (140 N·m)
Important Notes
Tighten in a star pattern. Important for wheel safety. Do not over-torque.

Brakes

Torque specifications for Brakes

Brake Caliper

1

Brake Caliper Bolts

M14 x 1.5
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the caliper to the mounting bracket or knuckle.
2

Brake Pad Retaining Pin/Bolt

M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated value, may vary based on design. Secures brake pads within the caliper.
3

Brake Bleeder Screw

M10 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Critical for bleeding the brake system. Do not over tighten.
4

Brake Line Fitting/Brake Hose to Caliper

M10 x 1.0
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Connects brake line or hose to caliper. Overtightening can cause leaks.

Brake Mounting Bracket

1

Brake Caliper Mounting Bracket Bolts

M16 x 1.5
Torque Specification
130 ft-lbs (175 N·m)
Important Notes
Secures bracket to the wheel hub/knuckle. High torque required.

Brake Rotor

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Secures the brake rotor to the wheel hub.

Abs Sensor

1

Wheel Speed Sensor/ABS Sensor Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the sensor. Overtightening can damage the sensor.

Dl382 Transmission

Torque specifications for Dl382 Transmission

Transmission Mounting

1

Transmission Mounting Bolts

M14 x 1.5
Torque Specification
37 ft-lbs (50 N�m)

Transmission Oil Pan

1

Transmission Oil Pan Bolts

M10 x 1.25
Torque Specification
8 ft-lbs (10 N�m)

Transmission Fluid System

1

Transmission Drain and Fill Plugs

M12 x 1.5
Torque Specification
30 ft-lbs (40 N�m)
2

Transmission Fluid Drain/Fill Plug

M12 x 1.5
Torque Specification
30 ft-lbs (40 N�m)

Transmission Case and Bellhousing

1

Transmission Case Bolts

M16 x 1.5
Torque Specification
40 ft-lbs (55 N�m)
Important Notes
Estimated value based on industry standards for similar transmission cases.
2

Transmission Bellhousing Bolts

M14 x 1.5
Torque Specification
30 ft-lbs (40 N�m)
Important Notes
Estimated value based on industry standards for similar transmission bellhousings.

Transmission Crossmember

1

Transmission Crossmember Bolts

M18 x 1.5
Torque Specification
50 ft-lbs (68 N�m)
Important Notes
Estimated value based on industry standards for similar transmission crossmembers.

Drivetrain

Torque specifications for Drivetrain

Engine Flywheel

1

Flywheel Bolts

M10 x 1.25 (Estimated)
Torque Specification
59 ft-lbs (80 N·m)
Important Notes
Ensure the flywheel is properly aligned before tightening bolts. Bolts must be tightened evenly. Bolt size is estimated, refer to specific service manual.

Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75 (Estimated)
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure transmission is properly aligned before tightening bolts. Bolt size is estimated, refer to specific service manual.
2

Transmission Bell Housing Bolts

M10 x 1.5 (Estimated)
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Ensure bell housing is properly aligned before tightening bolts. Bolt size is estimated, refer to specific service manual.

Transmission Components

1

Transmission Oil Pan Bolts

M6 x 1.0 (Estimated)
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even sealing pressure. Inch-lbs was converted to ft-lbs. Bolt size is estimated, refer to specific service manual.
2

Transmission Drain and Fill Plugs

M18 x 1.5 (Estimated)
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new sealing washers or O-rings. Bolt size is estimated, refer to specific service manual.

Driveshaft Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.25 (Estimated)
Torque Specification
81 ft-lbs (110 N·m)
Important Notes
Ensure the drive axle is properly seated before tightening bolts. Bolt size is estimated, refer to specific service manual.
2

CV Joint/Axle Nut

M24 x 1.5 (Estimated)
Torque Specification
177 ft-lbs (240 N·m)
Important Notes
Use new nut if specified in service manual. Bolt size is estimated, refer to specific service manual.
3

Propeller/Drive Shaft Bolts

M10 x 1.25 (Estimated)
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure driveshaft is properly aligned before tightening bolts. Bolt size is estimated, refer to specific service manual.
4

Drive Axle/Half Shaft Center Support Bearing Bolts

M8 x 1.25 (Estimated)
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure bearing is properly aligned before tightening bolts. Bolt size is estimated, refer to specific service manual.
5

Driveshaft Center Support Bearing Bracket Bolts

M8 x 1.25 (Estimated)
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Ensure bracket is properly aligned before tightening bolts. Bolt size is estimated, refer to specific service manual.

Differential

1

Differential Housing Mounting Bolts

M12 x 1.75 (Estimated)
Torque Specification
74 ft-lbs (100 N·m)
Important Notes
Ensure differential is properly aligned before tightening bolts. Bolt size is estimated, refer to specific service manual.
2

Differential Drain/Fill Plug

M18 x 1.5 (Estimated)
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new sealing washers or O-rings. Bolt size is estimated, refer to specific service manual.
3

Rear Differential Input Flange Nut

M20 x 1.5 (Estimated)
Torque Specification
147 ft-lbs (200 N·m)
Important Notes
Use new nut if specified in service manual. Bolt size is estimated, refer to specific service manual.

Transfer Case

1

Transfer Case Drain/Fill Plug

M18 x 1.5 (Estimated)
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Use new sealing washers or O-rings. Bolt size is estimated, refer to specific service manual.

Electrical

Torque specifications for Electrical

Electrical Ignition

1

Ignition Coil Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper seating of the coil before tightening.

Electrical Starting Charging

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure starter is properly aligned with the engine block before tightening.
2

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Ensure proper alternator alignment for correct belt tension.
3

Battery Terminal Nuts

M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Do not overtighten to avoid damage to battery terminals. Clean terminals before installation.

Electrical Fuel Injection

1

Fuel Injector Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper injector seating before tightening.

Electrical Engine Management

1

Throttle Body Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure throttle body is properly aligned before tightening.
2

Engine Control Unit (ECU) Mounting Bolts

M6 x 1.0
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
Estimated value. Do not over-tighten. Ensure proper seating and grounding of the ECU.
3

Ground Strap/Cable Connection Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure clean metal-to-metal contact for proper grounding.
4

Sensor Mounting Bolts (Crank, Cam, Wheel Speed, MAF, MAP etc.)

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
For larger sensor bolts, torque up to 15 ft-lbs (20 Nm). Estimated value, check per component.

Electrical Lighting

1

Headlight Mounting Bolts

M6 x 1.0
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment and sealing of the headlight unit.
2

Taillight Mounting Bolts

M6 x 1.0
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
Ensure proper alignment and sealing of the taillight unit.

Electrical Distribution

1

Fuse Box/Relay Box Mounting Bolts

M6 x 1.0
Torque Specification
7.5 ft-lbs (10 N·m)
Important Notes
Ensure the fuse/relay box is securely mounted to prevent vibration damage.
2

Wiring Harness Connector Mounting Bolts/Retaining Screws

M4 x 0.7
Torque Specification
2.5 ft-lbs (3.4 N·m)
Important Notes
Estimated value. Hand Tighten + 1/4 turn. Do not over-tighten. Ensure connector is fully seated.

Emissions Sensors

Torque specifications for Emissions_sensors

EGR System

1

EGR Valve Bolts

M10 x 1.5
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Proper torque ensures a secure connection and prevents leaks.

Oxygen Sensor System

1

Oxygen Sensor Bolts

M12 x 1.25
Torque Specification
17.5 ft-lbs (22.5 N·m)
Important Notes
Estimated value based on industry standards. Consult manufacturer's recommendations for specific torque values.

Catalytic Converter System

1

Catalytic Converter to Exhaust Pipe Bolts

M14 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Proper torque ensures a secure connection and prevents leaks.

NOx Sensor System

1

NOx Sensor Bolts

M10 x 1.25
Torque Specification
17.5 ft-lbs (22.5 N·m)
Important Notes
Estimated value based on industry standards. Consult manufacturer's recommendations for specific torque values.

Exhaust Gas Temperature Sensor System

1

Exhaust Gas Temperature Sensor Bolts

M12 x 1.25
Torque Specification
17.5 ft-lbs (22.5 N·m)
Important Notes
Estimated value based on industry standards. Consult manufacturer's recommendations for specific torque values.

Exhaust

Torque specifications for Exhaust

3.0l Engine Cylinder Head

1

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even gasket compression.

Exhaust System

1

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure proper alignment of flanges before tightening.
2

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the catalytic converter gasket is properly seated before tightening.
3

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Use new gaskets if available and tighten evenly to prevent leaks.

Exhaust Clamps

1

50-60mm Exhaust Clamp

Varies, typically M8
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value. Always verify clamp manufacturer specifications.
2

60-70mm Exhaust Clamp

Varies, typically M8 or M10
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated value. Always verify clamp manufacturer specifications.

Exhaust Sensors

1

Oxygen (O2) Sensor

M18 x 1.5 (typical)
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Estimated value. Torque may vary by sensor manufacturer and thread size. Do not overtighten.

Exhaust Hangers

1

Exhaust System Hanger Bolts/Nuts

Varies (M8 - M12 typical)
Torque Specification
18.5 ft-lbs (25 N·m)
Important Notes
Average estimated value. Torque may vary slightly based on specific bolt size and location. Use 15ft-lbs for smaller (M8) fasteners, 22ft-lbs for larger (M12) fasteners.

Fuel

Torque specifications for Fuel

Fuel System Fuel Rail

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure mating surfaces are clean prior to installation. Torque bolts in a cross pattern.
2

Fuel Injector Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure proper O-ring is in place on the injector. Torque bolts in a cross pattern.

Fuel System Fuel Pump

1

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the fuel pump O-ring is properly seated. Torque bolts evenly.

Fuel System Fuel Tank

1

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Torque all strap bolts evenly to avoid stress on the tank.

Fuel System Fuel Lines

1

Fuel Line Fittings to Fuel Rail/Pump/Injector

Refer to manufacturer's manual for specific fitting size
Torque Specification
15 ft-lbs (20 N·m)
Important Notes
Estimated value. *Refer to the manufacturer's specific manual for exact torque value of your fuel lines and components.* Torque specifications vary based on fitting size and material. Use proper flare nut wrench to prevent damage.
2

Fuel Pressure Sensor Bolts/Fitting

Refer to manufacturer's manual for specific fitting size
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value. *Refer to the manufacturer's specific manual for exact torque values.* Torque specifications vary based on sensor and fitting type. Do not over-tighten to avoid damage to the sensor.

Fuel System Misc

1

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure filler neck is properly aligned before tightening. Torque bolts evenly.
2

Fuel Filter Bolt/Nut

M8 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Use a proper wrench to avoid damage to the fuel filter housing.
3

Fuel Vapor Purge Valve/Solenoid Mounting Bolts

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value. *Refer to the manufacturer's specific manual for exact torque values.* Torque specifications vary based on sensor and fitting type. Do not over-tighten to avoid damage to the component.

Hvac

Torque specifications for Hvac

Hvac Compressor

1

A/C Compressor Mounting Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Ensure the compressor is properly aligned before tightening. Use a cross pattern during tightening.

Hvac Lines And Fittings

1

A/C Line Fittings

Varies, typically M8 x 1.25
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Over-tightening can damage fittings and cause leaks. Use a line wrench if possible.
2

Expansion Valve Mounting Bolts/Screws

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Ensure the expansion valve is properly seated before tightening. Over-tightening can crack the valve housing.
3

Refrigerant Pressure Sensor Mounting Bolt/Screw

M5 x 0.8
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Sensor can be damaged if over-tightened. Ensure proper seating before tightening.

Hvac Blower Motor

1

HVAC Blower Motor Mounting Bolts

M6 x 1.0 (Estimated)
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value. Confirm with service manual. These may also be self tapping screws. Do not over tighten. Use a cross pattern when tightening to evenly seat the blower motor.

Hvac Control Panel

1

HVAC Control Panel Mounting Screws

M4 x 0.7
Torque Specification
0.58 ft-lbs (1 N·m)
Important Notes
Low torque setting to prevent damage to plastic components. This value has been converted from inch-lbs to ft-lbs and N-m. Do not over tighten. Screws may be self-tapping into plastic

Hvac Evaporator Housing

1

HVAC Evaporator Housing Mounting Bolts/Screws

M6 x 1.0 (Estimated)
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Estimated value. Confirm with service manual. Do not over tighten, mounting is often into plastic.

Hvac Condenser

1

HVAC Condenser Mounting Bolts/Screws

M8 x 1.25
Torque Specification
18 ft-lbs (25 N·m)
Important Notes
Ensure the condenser is properly aligned before tightening. Use a cross pattern during tightening.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut/Shock Absorber Upper Mounting Bolts

M10 x 1.5
Torque Specification
30 ft-lbs (40 N·m)
Important Notes
Secures the top of the strut/shock assembly to the chassis or strut tower. Ensure bolts are clean and threads are in good condition.
2

Strut/Shock Absorber Lower Mounting Bolt(s) to Steering Knuckle

M14 x 1.5
Torque Specification
1. 81 ft-lbs (110 N·m) 2. 90°
Important Notes
Secures the bottom of the strut/shock assembly to the steering knuckle. This is a critical joint; torque to yield bolt must be replaced.
3

Control Arm Bolts

M12 x 1.75
Torque Specification
66 ft-lbs (90 N·m)
Important Notes
Connects control arms to the chassis and/or subframe. Ensure all bushings are seated correctly before tightening.
4

Ball Joint Nut

M12 x 1.5
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
Secures the ball joint to either the control arm or steering knuckle. Ensure proper seating of the ball joint before tightening.
5

Tie Rod End Nut

M10 x 1.25
Torque Specification
37 ft-lbs (50 N·m)
Important Notes
Secures the tie rod end to the steering knuckle. Ensure the tie rod end is correctly positioned before tightening.
6

Sway Bar Link Nut

M10 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Secures the sway bar link to the sway bar and strut or control arm. Tighten with suspension loaded if possible.
7

Steering Knuckle to Upper Control Arm Pinch Bolt

M12 x 1.75
Torque Specification
48 ft-lbs (65 N·m)
Important Notes
This pinch bolt clamps the upper control arm ball joint to the steering knuckle. Ensure correct alignment before tightening.

Rear Suspension

1

Rear Control Arm Inner Mounting Bolts

M12 x 1.75
Torque Specification
1. 66 ft-lbs (90 N·m) 2. 90°
Important Notes
Secures rear control arms to the subframe or chassis. Ensure proper alignment before tightening. Torque to yield bolt must be replaced.
2

Rear Control Arm Outer Mounting Bolt to Knuckle

M12 x 1.75
Torque Specification
1. 48 ft-lbs (65 N·m) 2. 90°
Important Notes
Secures rear control arms to the wheel hub carrier. Ensure proper alignment before tightening. Torque to yield bolt must be replaced.

Subframe

1

Front Subframe Bolts to Chassis

M14 x 2.0
Torque Specification
1. 80 ft-lbs (110 N·m) 2. 90°
Important Notes
Secures the front subframe to the vehicle's chassis. These bolts are commonly torque to yield and must be replaced. Ensure proper alignment before tightening.
2

Rear Subframe Bolts to Chassis

M14 x 2.0
Torque Specification
1. 80 ft-lbs (110 N·m) 2. 90°
Important Notes
Secures the rear subframe to the vehicle's chassis. These bolts are commonly torque to yield and must be replaced. Ensure proper alignment before tightening.

Sway Bar

1

Sway Bar Mounting Bracket Bolts to Chassis

M8 x 1.25
Torque Specification
25 ft-lbs (35 N·m)
Important Notes
Secures the sway bar mounting brackets to the chassis. Ensure proper alignment before tightening.

Wheel Speed Sensor

1

Wheel Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
7 ft-lbs (10 N·m)
Important Notes
Secures the wheel speed sensor to the steering knuckle or hub carrier. Be careful not to overtighten and damage the sensor.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the torque value for the wheel lug nuts on a 2018 Audi A6?

120 Nm (89 lb-ft)

Q2

How do I properly torque the spark plugs on my 2020 Audi A6?

20 Nm (15 lb-ft) + 90 degrees

Q3

What IS the recommended torque for the oil drain plug on a 2019 Audi A6?

30 Nm (22 lb-ft)

Q4

Can I use an impact wrench to torque bolts and nuts on my Audi A6?

No, an impact wrench can over-torque fasteners and damage threads. Use a calibrated torque wrench instead.

Q5

What are the torque specifications for the brake caliper bolts on a 2021 Audi A6?

120 Nm (89 lb-ft) for the front and 100 Nm (74 lb-ft) for the rear

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the A6.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Tightening Wheel Lug Nuts

Properly tightening wheel lug nuts IS crucial for safety. Follow these steps to ensure correct torque.

  • Clean the lug nuts and wheel studs thoroughly.
  • Apply a thin layer of anti-seize lubricant to the threads of the lug nuts.
  • Hand-tighten the lug nuts onto the studs as far as possible.
  • Use a digital torque wrench to tighten the lug nuts to 120 Nm (89 ft-lb).
  • Tighten the lug nuts in a star pattern to evenly distribute the force.
  • Recheck the torque of the lug nuts after driving approximately 100 km (60 miles).
View full procedure

Replacing Brake Pads

Replacing brake pads IS a critical safety procedure. Refer to this guide for detailed instructions.

  • Safety first: Park the vehicle on a level surface, engage the parking brake, and chock the wheels.
  • Remove the lug nuts and take off the wheel.
  • Remove the caliper mounting bolts and carefully lift the caliper off the rotor.
  • Remove the old brake pads and clean the caliper bracket.
  • Install the new brake pads and apply a thin layer of brake grease to the back of the pads.
  • Reinstall the caliper and tighten the mounting bolts to 120 Nm (89 ft-lb).
  • Reinstall the wheel and tighten the lug nuts to 120 Nm (89 ft-lb).
  • Pump the brake pedal several times to seat the new pads.
View full procedure
Technical Service Bulletins

TSB: Incorrect Torque Specifications for Engine Mounting Bolts

2020-06-15

This Technical Service Bulletin addresses an issue where incorrect torque specifications were provided for the engine mounting bolts on certain 2018-2020 A6 models. Using the incorrect torque can lead to premature bolt failure and engine damage.

2018-2020 A6

Resolution: Inspect the engine mounting bolts and ensure they are torqued to the correct specification of 50 Nm (37 ft-lb).

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Audi Specs. All rights reserved.

Privacy Policy Terms of Service