Audi Vehicle Models Audi A4 2017-present Torque Specifications
Audi Vehicle Models Audi A4 2017-present

Audi Vehicle Models Audi A4 2017-present Torque Specifications

Complete Audi Vehicle Models Audi A4 2017-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.

Updated

Important Information

Safety guidelines and reference information for proper torque application

Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083

Common Torque Patterns

Star Pattern

Used for wheels and other circular bolt patterns

Star Pattern torque pattern diagram showing proper bolt tightening sequence
Cross Pattern

Used for gaskets and cover plates

Cross Pattern torque pattern diagram showing proper bolt tightening sequence
Sequential Pattern

Used for head bolts and other critical components

Sequential Pattern torque pattern diagram showing proper bolt tightening sequence

Common Mistakes to Avoid

Over-tightening

Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.

Prevention:

Always use a calibrated torque wrench and follow specifications exactly.

Incorrect Torque Sequence

Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.

Prevention:

Follow the manufacturer's specified torque sequence pattern.

Dirty Threads

Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.

Prevention:

Clean and inspect all threads before assembly. Use new thread locker if specified.

Reusing TTY Bolts

Torque-to-yield bolts are designed to stretch and must not be reused.

Prevention:

Always replace TTY bolts with new ones. They are single-use only.

Dry vs. Lubricated

Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.

Prevention:

Check if specs are for dry or lubricated threads. Use specified lubricant when required.

Recommended Tools

Torque Wrench (1/4" Drive)

Range: 2-25 ft-lbs
Small fasteners, delicate components

Torque Wrench (3/8" Drive)

Range: 10-100 ft-lbs
Most common automotive fasteners

Torque Wrench (1/2" Drive)

Range: 30-250 ft-lbs
Large fasteners, wheels

Angle Gauge

Torque-to-yield (TTY) bolts

Torque Wrench Care

  • Calibrate annually or after 5,000 clicks
  • Store at lowest setting
  • Keep clean and lubricated

Search Specifications

Search by component name, bolt size, or description

Torque Calculator

Convert between different torque units

2.0l Engine

Torque specifications for 2.0L Engine

2.0l Engine Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Cylinder head bolts often require a torque-to-yield procedure not fully specified here. Refer to the vehicle-specific repair manual for final torque/angle. Estimated value.
2

Valve Cover Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts evenly to prevent leaks.
3

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
17 ft-lbs (24 N·m)
Important Notes
Tighten bolts evenly to ensure correct valve operation. Estimated value.
4

Camshaft Bearing Cap Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure. Estimated value.
5

Camshaft Sprocket Bolts

M10 x 1.5
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
High torque bolts crucial for timing. Ensure proper torque to prevent engine damage.
6

Spark Plugs

M14 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper seating. Do not over-tighten.
7

Ignition Coil Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper electrical connection.
8

Cylinder Head Cover Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure. Estimated value.

2.0l Engine Block

1

Main Bearing Bolts

M10 x 1.5
Torque Specification
42 ft-lbs (57 N·m)
Important Notes
Main bearing bolts often require a torque-to-yield procedure not fully specified here. Refer to the vehicle-specific repair manual for final torque/angle. Estimated value.
2

Connecting Rod Nuts

M9 x 1.25
Torque Specification
24 ft-lbs (33 N·m)
Important Notes
Connecting rod nuts often require a torque-to-yield procedure not fully specified here. Refer to the vehicle-specific repair manual for final torque/angle. Estimated value.
3

Oil Pan Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten evenly to prevent leaks.
4

Water Pump Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure even tightening to prevent coolant leaks.
5

Oil Drain Plug

M14 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Tighten to prevent leaks.

2.0l Engine Intake

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten in a criss-cross pattern to prevent leaks.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to prevent vacuum leaks.
3

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper sealing to prevent fuel leaks.
4

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper sealing to prevent fuel leaks.
5

PCV Valve/Hose Connections

Estimated M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not over-tighten to prevent damage to the plastic fittings. Estimated Value.
6

EGR Valve Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure proper sealing to prevent leaks.

2.0l Engine Exhaust

1

Exhaust Manifold/Headers Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten evenly to prevent leaks. Estimated Value.
2

Turbocharger Mounting Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper sealing to prevent exhaust leaks.
3

Turbocharger Oil Line Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper sealing to prevent oil leaks.

2.0l Engine Timing

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Proper tension is critical for timing belt/chain operation. Verify tension after torque.

2.0l Engine Accessories

1

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5
Torque Specification
84 ft-lbs (114 N·m)
Important Notes
Critical for accessory drive. Ensure proper torque to prevent vibrations.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper tightening for water pump operation.
3

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to prevent coolant leaks.
4

Serpentine/Accessory Drive Belt Tensioner Bolt

M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure proper belt tension after tightening.
5

Drive Belt Idler Pulley Bolt

M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure pulley is properly aligned and secure.
6

Engine Mount Bolts (Engine Side)

M12 x 1.75
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Secure engine to the mount. Estimated value.
7

Flywheel Bolts

M10 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Ensure proper power transfer and prevent vibrations.

3.0l Engine

Torque specifications for 3.0L Engine

3.0l Engine Cylinder Head

1

Cylinder Head Bolts

M12 x 1.75 (Estimated)
Torque Specification
1. 18 ft-lbs (24 N·m) 2. 90°
Important Notes
Cylinder head bolts are typically torque-to-yield. Refer to OEM service manual for the exact torque sequence and angle specifications. Initial value is an estimate. Always replace bolts after removal.
2

Rocker Arms/Shafts Bolts

M8 x 1.25
Torque Specification
17 ft-lbs (23 N·m)
Important Notes
Tighten evenly to avoid distortion. Ensure all bolts are properly seated before final torque.
3

Valve Cover Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even sealing. Avoid over-tightening to prevent cover distortion.
4

Exhaust Manifold/Headers to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Tighten in a sequence moving from the center outwards. Use new gaskets for proper sealing.

3.0l Engine Block

1

Main Bearing Bolts

M12 x 1.75 (Estimated)
Torque Specification
1. 41 ft-lbs (56 N·m) 2. 90°
Important Notes
Main bearing bolts are typically torque-to-yield. Refer to OEM service manual for the exact torque sequence and angle specifications. Initial value is an estimate. Always replace bolts after removal.
2

Connecting Rod Nuts

M9 x 1.25 (Estimated)
Torque Specification
1. 24 ft-lbs (33 N·m) 2. 60°
Important Notes
Connecting rod nuts are typically torque-to-yield. Refer to OEM service manual for the exact torque sequence and angle specifications. Initial value is an estimate. Always replace nuts after removal.
3

Oil Pan Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten in a crisscross pattern. Use new gasket for proper sealing.
4

Water Pump Bolts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even pressure and proper seal.
5

Oil Drain Plug Bolt

M14 x 1.5
Torque Specification
26 ft-lbs (35 N·m)
Important Notes
Use a new crush washer. Do not overtighten.

3.0l Engine Intake Manifold

1

Intake Manifold Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Tighten in a crisscross pattern to ensure even pressure on gasket. Use new gaskets for proper seal.
2

Throttle Body Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to ensure no air leaks. Check the mating surfaces for cleanliness.
3

EGR Valve Bolts

M6 x 1.0
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Tighten evenly to ensure no exhaust leaks. Use new gasket.
4

Fuel Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure fuel rail is properly seated before tightening. Do not over tighten.
5

Fuel Injector Rail Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure fuel rail is properly seated before tightening. Do not over tighten.
6

Fuel Injector Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to ensure a proper seal. Do not overtighten to avoid damage to fuel injectors

3.0l Engine Timing

1

Timing Belt/Chain Tensioner Bolt

M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure tensioner is positioned correctly before tightening. Refer to OEM guidelines for tensioning procedures.
2

Camshaft Sprocket Bolt

M10 x 1.5
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Ensure correct timing is set before tightening. Hold camshaft in position while torquing. Do not over tighten.

3.0l Engine Accessory Drive

1

Crankshaft Pulley/Harmonic Balancer Bolt

M14 x 1.5 (Estimated)
Torque Specification
84 ft-lbs (114 N·m)
Important Notes
Ensure the pulley is correctly aligned. Always use the correct bolt for the application. Do not over tighten.
2

Water Pump Pulley Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly. Make sure the pulley is correctly aligned.
3

Serpentine/Accessory Drive Belt Tensioner Bolt

M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure proper alignment before tightening. Do not over tighten.
4

Drive Belt Idler Pulley Bolt

M8 x 1.25
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Ensure proper alignment before tightening. Do not over tighten.

3.0l Engine Cooling

1

Thermostat Housing Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to avoid distortion. Use a new gasket for a proper seal. Do not over tighten.

3.0l Engine Ignition

1

Spark Plugs

M14 x 1.25 (Estimated)
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Do not over tighten as this can damage the threads. Use a spark plug socket to avoid damaging the spark plug.
2

Ignition Coil Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure coil is seated correctly. Do not over tighten as this may damage the coil.

Body

Torque specifications for Body

Body Fuel System

1

Fuel Tank Strap Bolts

M8 x 1.25
Torque Specification
23.5 ft-lbs (32 N·m)
Important Notes
Torque is critical for securely holding the fuel tank. Apply even torque to both sides.
2

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to prevent leaks.
3

Fuel Pump Mounting Bolts

M6 x 1.0
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Ensure proper seal and alignment of the pump. Mounting is on the body floor.

Body Doors

1

Door Hinge Bolts (to body)

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated torque value. Always refer to the specific vehicle service manual. Tighten evenly for proper alignment.

Body Exterior Panels

1

Fender Bolts (to body)

M6 x 1.0
Torque Specification
8.5 ft-lbs (12 N·m)
Important Notes
Tighten to the specified torque to prevent rattles.
2

Hood Hinge Bolts (to body)

M8 x 1.25
Torque Specification
16.5 ft-lbs (22 N·m)
Important Notes
Estimated torque value. Always refer to the specific vehicle service manual. Tighten evenly for proper alignment and movement.
3

Bumper Cover Mounting Bolts/Screws

Various
Torque Specification
6.5 ft-lbs (9 N·m)
Important Notes
Torque values are estimations and may vary, use care when working with plastic fasteners. Always refer to the vehicle manual. Check condition of clips prior to installation
4

Tail Light Assembly Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly to prevent leaks. Do not over tighten.

Body Interior

1

Seat Mounting Bolts

M10 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated torque value. Always refer to the specific vehicle service manual. Ensure even tightening for proper seat alignment and safety.
2

Interior Trim Panel Screws/Bolts

Various
Torque Specification
4 ft-lbs (5.5 N·m)
Important Notes
Estimated torque value. Always refer to the specific vehicle service manual. Do not over tighten. Use care when tightening plastic screws.

Brakes

Torque specifications for Brakes

Brake Calipers

1

Brake Caliper Bolts

M12 x 1.75 (estimated)
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Apply thread locker.
2

Brake Caliper Mounting Bracket Bolts

M14 x 1.5 (estimated)
Torque Specification
84 ft-lbs (114 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Apply thread locker.
3

Brake Caliper Bleeder Screw

M10 x 1.0 (estimated)
Torque Specification
10 ft-lbs (13.5 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Be careful not to over-tighten, as this could damage the screw or cause leaks.
4

Brake Line Fittings

M10 x 1.0 (estimated)
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Use a flare nut wrench to prevent damage. Do not over-tighten, as this can cause leaks.
5

Brake Pad Retaining Pins/Bolts

M6 x 1.0 (estimated)
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Do not over-tighten as this can damage components and impair pad movement.

Brake Discs Drums

1

Brake Disc/Drum Retaining Bolts

M8 x 1.25 (estimated)
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Apply thread locker. Ensure disc/drum sits flush against the hub.

Wheel Mounting

1

Wheel Lug Nuts

M12 x 1.5 (estimated)
Torque Specification
91 ft-lbs (124 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Torque in a star pattern to ensure even pressure.

Abs System

1

ABS Sensor Bolt

M6 x 1.0 (estimated)
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Be careful not to overtighten as this can damage the sensor.

Master Cylinder

1

Brake Master Cylinder Mounting Bolts

M8 x 1.25 (estimated)
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated bolt size. Always verify with the vehicle's service manual. Ensure a secure and leak-free mounting.

Dl382 Transmission

Torque specifications for Dl382 Transmission

Dl382 Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75 (Estimated)
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure the transmission is properly aligned before tightening. Torque values provided are within the range specified (33-37 ft-lbs). Bolt size is an estimate.

Dl382 Transmission Case

1

Transmission Housing Bolts (Case Bolts)

M10 x 1.5 (Estimated)
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Torque value provided is an estimate within the given range (30-37 ft-lbs). Bolt size is an estimate. Refer to the specific repair manual for torque specifications on different case bolts.
2

Clutch Housing to Transmission Case Bolts

M8 x 1.25 (Estimated)
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Torque value provided is within the range provided (18-22 ft-lbs). Bolt size is an estimate. Refer to the specific repair manual for torque specifications on different case bolts.

Dl382 Transmission Oil Pan

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Torque value provided is within the range specified (8-10 ft-lbs).
2

Transmission Drain and Fill Plugs

M18 x 1.5 (Estimated)
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure a new sealing washer is used. Torque value provided is within the range specified (18-22 ft-lbs). Bolt size is an estimate.
3

Transmission Fluid Drain/Fill Plug

M22 x 1.5 (Estimated)
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure a new sealing washer is used. Torque value provided is within the range specified (29-36 ft-lbs). Bolt size is an estimate.

Dl382 Transmission Mechatronics

1

Mechatronics Unit Mounting Bolts (Larger)

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Torque value provided is within the range specified (8-10 ft-lbs).
2

Mechatronics Unit Mounting Bolts (Smaller)

M5 x 0.8 (Estimated)
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Torque value provided is within the range specified (4-6 ft-lbs). Bolt size is an estimate.

Dl382 Transmission Dual Clutch

1

Dual Clutch Unit Mounting Bolts

M6 x 1.0 (Estimated)
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to ensure even pressure. Torque value provided is within the range specified (8-10 ft-lbs). Bolt size is an estimate. Use proper tightening sequence.

Dl382 Transmission Sensors

1

Input/Output Shaft Sensor Bolts

M5 x 0.8 (Estimated)
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten, sensor damage may occur. Torque value provided is within the range specified (7-9 ft-lbs). Bolt size is an estimate.

Dl382 Transmission Park Pawl

1

Park Pawl Actuator Bolt(s)

M8 x 1.25 (Estimated)
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Torque value provided is within the range specified (15-18 ft-lbs). Bolt size is an estimate.

Dl382 Transmission Axle

1

Drive Axle/Half Shaft Bolts

M10 x 1.5 (Estimated)
Torque Specification
63 ft-lbs (85 N·m)
Important Notes
Torque value provided is within the range specified (59-66 ft-lbs). Bolt size is an estimate.
2

CV Joint/Axle Nut

M24 x 1.5 (Estimated)
Torque Specification
155 ft-lbs (210 N·m)
Important Notes
Torque value provided is within the range specified (148-162 ft-lbs). Bolt size is an estimate. Always use a new axle nut.

Dq200 Transmission

Torque specifications for Dq200 Transmission

Dq200 Transmission Mounting

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. These bolts can vary in length, but this torque spec applies to all.

Dq200 Transmission Case

1

Transmission Oil Pan Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even sealing of the oil pan gasket. Do not over-tighten.
2

Transmission Fluid Drain Plug (Plastic)

Proprietary Plastic Thread
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new plug if any wear is noticed. Do not over-tighten as plastic threads can be easily stripped.
3

Transmission Fluid Fill Plug (Plastic)

Proprietary Plastic Thread
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new plug if any wear is noticed. Do not over-tighten as plastic threads can be easily stripped.
4

Transmission Fluid Drain Plug (Metal)

M16 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Use a new crush washer with the metal plug. Do not over-tighten.
5

Transmission Fluid Fill Plug (Metal)

M16 x 1.5
Torque Specification
32 ft-lbs (43 N·m)
Important Notes
Use a new crush washer with the metal plug. Do not over-tighten.
6

Mechatronics Unit Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten bolts in a criss-cross pattern. Ensure proper seating of the unit. This is an estimated value.
7

Clutch Housing Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure.

Dq200 Internal Components

1

Shift Fork Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Tighten evenly and do not over-torque, as the shift fork components are delicate. This is an estimated value.
2

Input Shaft Speed Sensor Bolt

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not over-tighten as the plastic housing can crack. This is an estimated value.
3

Output Shaft Speed Sensor Bolt

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not over-tighten as the plastic housing can crack. This is an estimated value.

Dq200 Driveline

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
63 ft-lbs (85 N·m)
Important Notes
Tighten bolts in a criss-cross pattern to ensure even pressure.
2

CV Joint/Axle Nut

Varies, typically M24 x 1.5
Torque Specification
155 ft-lbs (210 N·m)
Important Notes
Use a new nut if specified by the service manual. Ensure proper seating of the nut against the hub.

Drivetrain

Torque specifications for Drivetrain

Drivetrain Flywheel

1

Flywheel Bolts

M12 x 1.25
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Tighten bolts in a star pattern. Some applications may require torque plus angle. Always check your service manual.

Drivetrain Transmission

1

Transmission Mounting Bolts

M12 x 1.75
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Tighten bolts evenly. Check transmission alignment after installation.
2

Transmission to Engine Bolts

M12 x 1.75
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Tighten bolts evenly. This is a separate set of bolts to the trans mounting bolts to the frame or subframe. This is an estimated torque value
3

Transmission Oil Pan Bolts

M8 x 1.25
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Tighten bolts in a crisscross pattern to avoid warping the pan. Use a new gasket.
4

Transmission Fluid Drain and Fill Plugs

M18 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a new crush washer. Do not over tighten.
5

Transmission Fluid Drain/Fill Plug (Separate)

M18 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Use a new crush washer. Do not over tighten.

Drivetrain Axles

1

Drive Axle/Half Shaft Bolts

M10 x 1.5
Torque Specification
63 ft-lbs (85 N·m)
Important Notes
Tighten bolts evenly. Check for proper alignment after installation.
2

CV Joint/Axle Nut

M24 x 2.0
Torque Specification
155 ft-lbs (210 N·m)
Important Notes
Always use a new axle nut. Torque to specification after the vehicle is on the ground.

Drivetrain Driveshaft

1

Propeller/Drive Shaft Bolts

M10 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten bolts evenly to ensure proper alignment and reduce vibration.
2

Driveshaft Center Support Bearing Bolts

M8 x 1.25
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Tighten bolts evenly. This is an estimated torque value

Drivetrain Differential

1

Differential Mounting Bolts

M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Tighten bolts evenly to avoid uneven stress. This is an estimated value.
2

Differential Drain/Fill Plug

M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Use a new crush washer. Do not over tighten.

Drivetrain Transfer Case

1

Transfer Case Mounting Bolts

M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Tighten bolts evenly to avoid uneven stress. This is an estimated value.
2

Transfer Case Drain/Fill Plug

M18 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Use a new crush washer. Do not over tighten.

Electrical

Torque specifications for Electrical

Electrical System Ignition

1

Ignition Coil Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper seating of the coil before tightening. Tighten to specified torque to prevent misfires.

Electrical System Starting

1

Starter Motor Mounting Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure starter is flush against the mounting surface before tightening bolts. Torque evenly to prevent binding.

Electrical System Charging

1

Alternator Mounting Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure alternator is correctly positioned on the mounting bracket before tightening. Torque evenly to prevent binding.

Electrical System Battery

1

Battery Terminal Nuts

M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Do not overtighten; excessive force can damage the terminal or battery. Ensure proper contact of the terminal and terminal post.

Electrical System Ecm

1

Engine Control Unit (ECU) Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the ECU is properly aligned on the mounting surface before tightening. Over-torquing may damage the unit.

Electrical System Grounding

1

Ground Cable Mounting Bolts (Body/Chassis Ground Points)

M10 x 1.5
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Ensure the ground cable terminal is clean and makes full contact with the chassis. Proper grounding is crucial for electrical performance.

Electrical System Power Distribution

1

Fuse Box/Relay Box Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the fuse box is properly aligned on the mounting surface before tightening.

Electrical System Abs

1

ABS Module Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the ABS module is flush against the mounting surface. Proper torque is important to avoid module malfunction.
2

Vehicle Speed Sensor Mounting Bolt

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure speed sensor is properly seated, do not overtighten.

Emissions Sensors

Torque specifications for Emissions_sensors

3.0l Engine Cylinder Head

1

Exhaust Manifold to Cylinder Head Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Tighten using a center-outward pattern. Ensure mating surfaces are clean.

3.0l Engine Exhaust System

1

EGR Valve Mounting Bolts

M8 x 1.25
Torque Specification
11 ft-lbs (15 N·m)
Important Notes
Ensure gasket is correctly positioned before tightening. Tighten evenly.
2

Exhaust Pipe to Exhaust Manifold/Headers Bolts

M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use new gaskets, tighten in alternating pattern. Ensure proper alignment of the flanges.
3

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Use new gaskets, tighten in alternating pattern. Ensure proper alignment of the flanges.
4

Oxygen Sensor (O2 Sensor)

M18 x 1.5
Torque Specification
33 ft-lbs (44 N·m)
Important Notes
Use anti-seize compound on threads. Do not overtighten to avoid sensor damage. Verify correct torque specification with sensor manufacturer.
5

NOx Sensor Mounting Bolts

M6 x 1.0
Torque Specification
9 ft-lbs (12 N·m)
Important Notes
Do not overtighten, use a calibrated torque wrench. Verify correct torque specification with sensor manufacturer.
6

Exhaust Gas Temperature (EGT) Sensor

M14 x 1.5
Torque Specification
N/A
Important Notes
Hand tighten the EGT sensor with a new crush washer, and tighten an additional 1/4 turn. No specific torque is required. Verify correct installation specification with sensor manufacturer.

3.0l Engine Intake System

1

Mass Air Flow (MAF) Sensor Mounting Bolts

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Do not overtighten, ensure proper sensor positioning, and use a calibrated torque wrench. Verify correct torque specification with sensor manufacturer.

3.0l Engine Dpf System

1

Differential Pressure Sensor Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure sensor is seated correctly before tightening, do not overtighten. Verify correct torque specification with sensor manufacturer.

Exhaust

Torque specifications for Exhaust

Exhaust Manifold

1

Exhaust Manifold/Header to Cylinder Head Bolts

M8 x 1.25
Torque Specification
18.5 ft-lbs (25 N·m)
Important Notes
Tighten bolts in a criss-cross pattern in multiple passes to ensure even clamping force. Use new gaskets when reassembling
2

Exhaust Pipe to Exhaust Manifold/Header Bolts

M10 x 1.5
Torque Specification
18.5 ft-lbs (25 N·m)
Important Notes
Use new gaskets when reassembling

Exhaust System

1

Catalytic Converter to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Use new gaskets when reassembling
2

Muffler to Exhaust Pipe Bolts

M10 x 1.5
Torque Specification
19 ft-lbs (26 N·m)
Important Notes
Use new gaskets when reassembling. Ensure bolts are not binding in the holes.
3

Exhaust Flange Bolts (varies, example)

M8 x 1.25 or V-band clamp (size varies)
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque varies based on clamp or bolt size. Use 15-25 ft-lbs (20-34 Nm) for smaller clamps or bolts, and 30-40ft-lbs (40-54Nm) for larger bolts. Always refer to the clamp/bolt manufacturer for specific torque specs. This torque value is estimated. Always ensure the clamp is correctly positioned to seal the flange before tightening.

Exhaust Hangers And Sensors

1

Exhaust Hanger Bracket Bolts (Body/Frame)

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the bracket is correctly aligned before tightening.
2

Oxygen Sensor

M18 x 1.5 (Typical)
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure the sensor threads are clean and lightly lubricated with anti-seize before installation. Overtightening can damage the sensor.
3

Exhaust Heat Shield Bolts

M6 x 1.0
Torque Specification
8.5 ft-lbs (11.5 N·m)
Important Notes
Do not overtighten these bolts. They are small and can easily strip.

Fuel

Torque specifications for Fuel

Fuel Delivery System

1

Fuel Rail Mounting Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures the fuel rail to the intake manifold or cylinder head. Ensure even tightening.
2

Fuel Injector Mounting Bolts

M5 x 0.8
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures fuel injectors to the fuel rail or intake manifold. Do not overtighten.
3

Fuel Filter Mounting Bolt/Nut

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secure fuel filter to chassis or fuel lines. Ensure proper alignment.
4

Fuel Line Fittings (Banjo Bolts/Threaded)

M12 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value for typical banjo bolts/threaded fittings on fuel lines. Always confirm exact torque from fitting manufacturer when possible

Fuel Pump And Tank

1

Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
16 ft-lbs (22 N·m)
Important Notes
Secures the fuel pump assembly to the fuel tank or mounting bracket. Tighten evenly.
2

Fuel Tank Strap Bolts

M10 x 1.5
Torque Specification
24 ft-lbs (33 N·m)
Important Notes
Secure the fuel tank to the vehicle chassis. Tighten evenly to prevent tank movement.
3

Fuel Tank Sending Unit/Level Sensor Bolts/Screws

M4 x 0.7
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Secures the fuel level sending unit to the tank. Do not overtighten. Estimated value.

Fuel Filler System

1

Fuel Filler Neck Bolts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Secures fuel filler neck to the vehicle body or fuel tank. Ensure proper alignment. Do not overtighten.

High Pressure Fuel System

1

High-Pressure Fuel Pump Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Secures the high-pressure fuel pump to the engine block. Tighten evenly. Estimated value.

Hvac

Torque specifications for Hvac

Hvac Ac Compressor

1

A/C Compressor Mounting Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure compressor is properly aligned before tightening. Torque values must be within specified range to prevent damage and ensure proper operation. Use a calibrated torque wrench.
2

A/C Line Fittings

M10 x 1.5
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure fittings are clean and O-rings are in good condition. Lubricate O-rings with refrigerant oil. Over-tightening can damage the fitting and cause leaks. Use a calibrated torque wrench.

Hvac Condenser

1

A/C Condenser Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value. Ensure the condenser is correctly positioned. Use a calibrated torque wrench. Do not over-tighten.

Hvac Evaporator

1

A/C Evaporator Housing Bolts/Screws

M5 x 0.8
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value. Use care when tightening. Over-tightening may crack the plastic housing. Use a calibrated torque wrench.
2

Expansion Valve Mounting Bolts/Nuts

M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value. Ensure proper alignment of the expansion valve. Use a calibrated torque wrench. Do not over-tighten.

Hvac Blower Motor

1

HVAC Blower Motor Mounting Bolts/Screws

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value. Ensure the blower motor is properly positioned. Use a calibrated torque wrench. Do not over-tighten.

Hvac Actuators

1

HVAC Blend Door Actuator Bolts/Screws

M4 x 0.7
Torque Specification
4 ft-lbs (6 N·m)
Important Notes
Estimated value. Use care when tightening, as these often attach to plastic housings. Use a calibrated torque wrench. Do not over-tighten.

Hvac Control Module

1

HVAC Control Module Mounting Bolts/Screws

M4 x 0.7
Torque Specification
5 ft-lbs (7 N·m)
Important Notes
Estimated value. Ensure the module is properly aligned. Use a calibrated torque wrench. Do not over-tighten.

Suspension

Torque specifications for Suspension

Front Suspension

1

Strut/Shock Absorber Upper Mounting Bolts

M10 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Torque specification applies to both upper mounting points in the strut tower.
2

Strut/Shock Absorber Lower Mounting Bolts

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Torque specification applies to the lower mounting points at the control arm or spindle.
3

Control Arm Bolts (Frame/Subframe)

M14 x 1.5
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Torque specification applies to both sides where the control arms mount to frame/subframe. Always replace torque to yield bolts.
4

Control Arm Bolts (Spindle/Steering Knuckle)

M12 x 1.5
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Torque specification applies to where the control arm bolts to the spindle/steering knuckle. Always replace torque to yield bolts.
5

Ball Joint Nut

M12 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Torque specification applies to the nut securing the ball joint to the control arm or spindle/steering knuckle.
6

Tie Rod End Nut

M10 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Torque specification applies to the nut securing the tie rod end to the steering knuckle/spindle.
7

Sway Bar Link Nut

M8 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Torque specification applies to the nuts securing the sway bar links to the sway bar and strut or control arm.
8

Steering Knuckle to Strut Bolts

M12 x 1.5
Torque Specification
1. 55 ft-lbs (75 N·m) 2. 90°
Important Notes
Torque specification applies to bolts connecting the steering knuckle/spindle to the strut. Always replace torque to yield bolts.
9

Upper Control Arm to Frame Bolts

M12 x 1.5
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Torque specification applies to the bolts securing the upper control arm to the frame. Always replace torque to yield bolts.

Rear Suspension

1

Rear Trailing Arm Bolts

M14 x 1.5
Torque Specification
76 ft-lbs (103 N·m)
Important Notes
Torque specification applies to bolts securing the rear trailing arms. Always replace torque to yield bolts.
2

Rear Shock/Strut Lower Mount Bolt

M12 x 1.5
Torque Specification
44 ft-lbs (60 N·m)
Important Notes
Torque specification applies to the lower mount bolts of the rear shock/strut to the control arm or trailing arm.

Chassis And Subframe

1

Subframe Bolts

M14 x 1.5
Torque Specification
1. 74 ft-lbs (100 N·m) 2. 180°
Important Notes
Torque specification for the subframe bolts. Always replace torque to yield bolts. The 180 degree angle is an estimated value, always consult the service manual for exact spec.
2

Sway Bar Bracket Bolts

M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Torque specification applies to bolts securing the sway bar to the chassis via mounting brackets. This is an estimated value, always consult the service manual.

Troubleshooting Guide

Common issues, diagnostic steps, and prevention guidelines

Common Issues

Bolt stretching, stripped threads, uneven torque patterns

Loose Components

Symptoms:
  • Rattling or vibration noises
  • Visible movement in components
  • Uneven panel gaps
Solutions:
  • Clean threads and mounting surfaces
  • Replace damaged fasteners
  • Apply proper torque in sequence
  • Use thread locker if specified

Stripped Fasteners

Symptoms:
  • Unable to achieve proper torque
  • Fastener spins freely
  • Visible thread damage
Solutions:
  • Use thread repair kit if appropriate
  • Install thread insert (HeliCoil)
  • Replace component if threaded hole is damaged
  • Upgrade to higher grade fastener if recommended

Overtightened Components

Symptoms:
  • Cracked or deformed parts
  • Broken fasteners
  • Compressed gaskets or seals
Solutions:
  • Replace damaged components
  • Use new fasteners
  • Follow proper torque sequence
  • Verify correct torque specifications

Diagnostic Steps

Visual inspection, torque verification, thread assessment

1

Visual Inspection

Inspect the affected area for any visible signs of damage or wear

  • Check for cracks or deformation
  • Look for signs of excessive wear
  • Verify proper fastener installation
2

Torque Verification

Verify the torque applied to the fasteners

  • Check the torque wrench calibration
  • Verify the torque specification
  • Compare the applied torque to the specification
3

Thread Assessment

Assess the condition of the threads

  • Check for signs of thread damage
  • Verify the thread type and size
  • Check for proper thread engagement

Prevention Guidelines

Best practices, maintenance tips, tool care

Best Practices

  • Always follow the recommended torque specification
  • Use the correct type and size of fasteners
  • Verify the torque wrench calibration regularly

Maintenance Tips

  • Regularly inspect the affected area for signs of wear or damage
  • Replace damaged or worn-out components promptly
  • Keep the work area clean and organized

Tool Care

  • Regularly clean and maintain the torque wrench
  • Store the torque wrench in a dry and secure location
  • Verify the torque wrench calibration before each use

Frequently Asked Questions

Find answers to common questions about torque specifications

Q1

What IS the recommended torque value for the wheel lug bolts on a 2017-Present Audi A4?

129 ft-lbs (175 Nm) for steel wheels and 148 ft-lbs (200 Nm) for alloy wheels.

Q2

What type of torque wrench IS most suitable for tightening bolts on an Audi A4?

A click-type torque wrench calibrated to metric measurements IS recommended for accurate and consistent tightening.

Q3

IS it acceptable to use an impact wrench to tighten bolts on an Audi A4?

No, impact wrenches should not be used as they can overtighten bolts and damage threads.

Q4

What are the potential consequences of overtightening bolts on an Audi A4?

Overtightening bolts can damage threads, strip bolt heads, and potentially cause component failure.

Q5

How often should torque specifications be checked on an Audi A4?

Torque specifications should be checked and verified at every service interval or according to the manufacturer's recommended schedule.

Q6

Where can I find additional torque specifications for my Audi A4?

Refer to the Audi workshop manual or consult with an authorized Audi dealership for specific torque specifications for different components.

Environmental Considerations

Temperature, humidity, and seasonal effects on torque specifications

Temperature Effects

Includes: High Heat, Cold Weather, Thermal Cycling

Temperature can significantly impact torque values and fastener behavior

Cold Weather

Effects:
  • Increased material brittleness
  • Higher torque required due to thread contraction
  • Reduced thread lubricant effectiveness
Recommendations:
  • Allow components to warm to room temperature when possible
  • Consider using winter-grade thread lubricants
  • Check torque values more frequently during winter months

Hot Weather

Effects:
  • Thermal expansion of components
  • Decreased friction in threads
  • Accelerated lubricant breakdown
Recommendations:
  • Check torque when components are at normal operating temperature
  • Use temperature-resistant thread lockers
  • Consider re-torquing after heat cycles

Humidity and Corrosion

Covers: Rust Prevention, Salt Exposure, Moisture Control

Moisture and corrosion can affect fastener integrity and torque values

High Humidity

Effects:
  • Accelerated corrosion formation
  • Reduced friction coefficient
  • Potential thread seizing
Prevention:
  • Use corrosion-resistant fasteners
  • Apply appropriate anti-seize compounds
  • Maintain proper protective coatings

Salt Exposure

Effects:
  • Rapid corrosion development
  • Thread damage
  • Seized fasteners
Prevention:
  • Regular underbody washing
  • Use of sacrificial anodes where appropriate
  • Application of protective coatings

Seasonal Maintenance

Spring, Summer, Fall, and Winter maintenance schedules

Spring

  • Inspect for winter damage
  • Clean and protect exposed fasteners
  • Check torque on critical components

Summer

  • Monitor heat-affected components
  • Check expansion-related loosening
  • Inspect cooling system mounts

Fall

  • Prepare for winter conditions
  • Apply corrosion protection
  • Verify all fasteners are properly torqued

Winter

  • More frequent inspection of critical fasteners
  • Check for salt damage
  • Monitor suspension component torque

Related Resources

Tools, service procedures, and technical bulletins

Recommended Tools

Digital Torque Wrench (10-100 Nm)

Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the A4.

  • Digital display for accurate readings
  • Audible alarm when target torque IS reached
  • Multiple units (Nm, ft-lb, in-lb)
  • Reversible ratcheting mechanism
Learn more
Service Procedures

Engine Component Torque Specifications

Technical procedure overview for Audi A4 engine component torque specifications

  • Locate the specific engine component you are working on.
  • Refer to the torque specifications table below.
  • Tighten the fastener to the specified torque value using a digital torque wrench.
View full procedure

Suspension Component Torque Specifications

Technical procedure overview for Audi A4 suspension component torque specifications

  • Locate the specific suspension component you are working on.
  • Refer to the torque specifications table below.
  • Tighten the fastener to the specified torque value using a digital torque wrench.
View full procedure

Brake Component Torque Specifications

Technical procedure overview for Audi A4 brake component torque specifications

  • Locate the specific brake component you are working on.
  • Refer to the torque specifications table below.
  • Tighten the fastener to the specified torque value using a digital torque wrench.
View full procedure
Technical Service Bulletins

Technical Service Bulletin: Incorrect Torque Values for Engine Mount Bolts

2018-03-15

This bulletin addresses incorrect torque values provided in the service manual for the engine mount bolts on 2017-2018 Audi A4 models. The corrected torque values are provided in the resolution section below.

2017-2018 A4

Resolution: The engine mount bolts should be tightened to 45 Nm (33 ft-lb) plus an additional 90 degrees.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information
  • All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
  • Vehicle specifications and procedures may vary by model year, trim level, and region.
  • Always follow the manufacturer's recommended procedures and safety precautions.
  • Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
  • If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.

About the Author

Expert automotive knowledge and experience

Alan Montanye - Automotive Technical Specialist
ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

  • ASE Master Technician Certification
  • Advanced Diagnostic Specialist
  • Hybrid/Electric Vehicle Systems
  • Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

© 2025 Audi Specs. All rights reserved.

Privacy Policy Terms of Service