Audi Audi RS5 2010-2016

Audi Audi RS5 2010-2016 Drivetrain Specifications

Detailed technical specifications and maintenance guidelines for the 2010-2016 Audi RS5 drivetrain system, including the quattro all-wheel-drive, 7-speed S tronic transmission, and torque vectoring.

Updated Oct 24, 2023

Overview Specifications

Comprehensive description of the drivetrain specifications for the 2010-2016 Audi RS5, including key features, measurements, and technical details

How to Use

Use the search function to locate specific drivetrain components or specifications by entering keywords such as 'transmission', 'differential', or 'torque split'.

Navigate through the drivetrain documentation sections using the table of contents or by scrolling through the document. Each section is clearly labeled for easy access.

Key Specifications

Engine Displacement

4.2L

Power Output

450 hp

Torque

317 lb-ft

Transmission

7-speed S tronic

Weight Distribution

56% front, 44% rear

Available Specifications

Engine and Transmission

Details about the engine and transmission system, including specifications and performance metrics

Engine Specifications

4.2L V8 FSI naturally aspirated engine
Power output: 450 hp at 8250 rpm
Torque: 317 lb-ft at 4000-6000 rpm
Redline: 8500 rpm
Compression ratio: 12.5:1

Transmission System

7-speed S tronic dual-clutch automatic transmission
Gear ratios: 1st (3.78), 2nd (2.18), 3rd (1.52), 4th (1.14), 5th (0.92), 6th (0.78), 7th (0.67)
Final drive ratio: 3.889
Quattro all-wheel drive system with torque vectoring
Launch control system included

Note: The S tronic transmission provides rapid gear shifts and optimized performance for both manual and automatic modes.

Differential and Driveshaft

Information about the differential and driveshaft components, including torque distribution and technical details

Differential Specifications

Crown gear center differential with torque split
Default torque distribution: 40% front, 60% rear
Dynamic torque vectoring for enhanced cornering
Mechanical locking function for improved traction
Weight: 22.5 kg (49.6 lbs)

Driveshaft Details

Carbon fiber-reinforced driveshaft
Length: 1.2 m (47.2 in)
Weight: 8.5 kg (18.7 lbs)
Designed for high torque and rotational speed
Reduces rotational mass for improved performance

Note: The carbon fiber driveshaft contributes to weight reduction and enhances drivetrain efficiency.

All-Wheel Drive System

Technical details about the Quattro all-wheel drive system, including torque distribution and performance features

Quattro System Overview

Permanent all-wheel drive system
Torque distribution adjustable based on driving conditions
Maximum torque to rear axle: 85%
Maximum torque to front axle: 70%
Integrated with Audi Drive Select for customizable performance

Performance Features

Dynamic torque vectoring for improved handling
Enhanced traction in low-grip conditions
Optimized weight distribution for balanced performance
Integrated with stability control systems
Supports launch control for maximum acceleration

Note: The Quattro system is designed to provide superior grip and stability in all driving conditions.

Suspension and Chassis

Details about the suspension and chassis components that interact with the drivetrain

Suspension System

Front suspension: Five-link design with aluminum components
Rear suspension: Trapezoidal-link design with aluminum components
Dynamic Ride Control (DRC) system included
Adjustable damping for sport and comfort modes
Lowered ride height by 20 mm (0.79 in) compared to standard A5

Chassis Specifications

Aluminum-intensive chassis for weight reduction
Torsional rigidity: 25,000 Nm/degree
Weight distribution: 56% front, 44% rear
Integrated subframes for improved stiffness
Designed for high-speed stability and agility

Note: The lightweight chassis and advanced suspension system enhance the drivetrain's performance and handling.

Search Specifications

Search by specification name, value, or description

Component Specifications

Engine

Type: 4.2L V8 FSI

Displacement: 4163 cc

Power Output: 450 hp @ 8250 rpm

Torque: 317 lb-ft @ 4000-6000 rpm

Compression Ratio: 12.5:1

Redline: 8500 rpm

Transmission

Type: 7-speed S tronic dual-clutch automatic

Gear Ratios: 1st: 4.714:1
2nd: 3.143:1
3rd: 2.106:1
4th: 1.667:1
5th: 1.286:1
6th: 1.034:1
7th: 0.839:1
Reverse: 3.317:1

Final Drive Ratio: 3.889:1

Part Number: 0B5 300 043 Q

Driveshaft

Material: High-strength steel

Length: 72.5 inches

Diameter: 2.5 inches

Part Number: 8T0 521 101 A

Differential

Type: Quattro all-wheel drive with crown gear center differential

Front Differential Ratio: 3.889:1

Rear Differential Ratio: 3.889:1

Torque Split: 40:60 front to rear (default)

Part Number: 0B5 525 010 B

Axles

Front Axle Type: Independent double wishbone

Rear Axle Type: Independent trapezoidal link

Axle Shaft Diameter: 1.5 inches

Part Number Front: 8T0 407 271 C

Part Number Rear: 8T0 407 272 D

Clutch

Type: Dual wet clutch

Clutch Pack Diameter: 8.5 inches

Clutch Material: Carbon fiber reinforced

Part Number: 0B5 141 033 A

Transfer Case

Type: Electronically controlled

Fluid Capacity: 1.5 liters

Fluid Type: G 052 145 A2

Part Number: 0B5 525 010 C

Propeller Shaft

Material: Aluminum

Length: 45.3 inches

Diameter: 3.0 inches

Part Number: 8T0 521 101 B

Wheel Bearings

Front Wheel Bearing Type: Sealed roller bearing

Rear Wheel Bearing Type: Sealed roller bearing

Front Bearing Part Number: 8T0 407 625 A

Rear Bearing Part Number: 8T0 407 626 B

Drivetrain Fluids

Engine Oil: Type: Synthetic 5W-40
Capacity: 9.3 liters
Specification: VW 502 00

Transmission Fluid: Type: G 052 529 A2
Capacity: 7.2 liters
Specification: VW TL 521 82

Differential Fluid: Type: G 052 145 A2
Capacity: 1.5 liters
Specification: VW TL 521 82

Service Information Service

Detailed service requirements and schedules for the 2010-2016 Audi RS5 drivetrain

10000

Engine oil and filter change
Inspect drivetrain components for leaks
Check transmission fluid level

Use only Audi-approved fluids and filters

40000

Replace transmission fluid
Inspect differential fluid
Check and replace wheel bearings if necessary

Follow Audi-specific torque specifications during reassembly

60000

Inspect and replace clutch pack if necessary
Check propeller shaft for wear
Inspect driveshaft for balance and alignment

Use Audi diagnostic tools for accurate assessment

Frequently Asked Questions

Find answers to common questions about torque specifications

What type of drivetrain does the 2010-2016 Audi RS5 use?

The 2010-2016 Audi RS5 features a quattro all-wheel-drive system with a self-locking center differential. This system distributes torque asymmetrically, with a default 40:60 front-to-rear torque split, enhancing handling and traction.

What is the gearbox configuration in the Audi RS5?

The Audi RS5 is equipped with a 7-speed S tronic dual-clutch transmission, which provides rapid gear shifts and optimized performance. The transmission supports both automatic and manual shift modes, with paddle shifters on the steering wheel.

What is the torque capacity of the drivetrain in the Audi RS5?

The drivetrain in the Audi RS5 is designed to handle up to 450 Nm (332 lb-ft) of torque, which is the maximum torque output of the 4.2-liter V8 FSI engine. The drivetrain components are engineered to withstand high-performance driving conditions.

How does the quattro system improve handling in the RS5?

The quattro all-wheel-drive system in the RS5 uses a self-locking center differential that dynamically adjusts torque distribution between the front and rear axles based on driving conditions. This improves traction, stability, and cornering performance, especially in adverse weather or high-speed scenarios.

What maintenance is required for the RS5 drivetrain?

Regular maintenance for the RS5 drivetrain includes checking and replacing the differential fluid every 40,000 miles (64,000 km), inspecting the driveshaft and CV joints for wear, and ensuring the transmission fluid is replaced according to Audi's recommended service intervals (typically every 60,000 miles or 96,000 km).

Factory Service Resources

Access official service manuals, technical documents, and repair guides. These resources provide detailed procedures, specifications, and diagrams directly from the manufacturer.

Audi RS5 Drivetrain Technical Overview

Coming Soon

A detailed technical guide covering the quattro all-wheel-drive system, transmission, and differential components specific to the 2010-2016 Audi RS5.

Quattro System Maintenance Guide

Coming Soon

Step-by-step instructions for maintaining and servicing the quattro all-wheel-drive system, including fluid changes and component inspections.

Audi RS5 Transmission Service Manual

Coming Soon

Official service manual for the 7-speed S tronic dual-clutch transmission, including troubleshooting, repair procedures, and torque specifications.

High-Performance Driving Tips for Audi RS5

Coming Soon

A guide to optimizing drivetrain performance during high-performance driving, including tips on managing torque distribution and transmission settings.

About the Author

Expert automotive knowledge and experience

ASE

Alan Montanye

Automotive Technical Specialist

ASE Master Certified Technician with over a decade of hands-on experience in automotive repair and diagnostics.

Facebook Contact

15+ Years

Experience

500+ Guides

Guides

50+ Makes

Vehicles

1000+ Solutions

Solutions

Diagnostic

Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.

Repair

Expert in both traditional mechanical repairs and modern vehicle systems.

Additional Expertise

Documentation

Created over 500 detailed repair guides and technical documents.

Training

Conducted technical training sessions and contributed to repair databases.

Certifications & Research

Certifications

ASE Master Technician Certification
Advanced Diagnostic Specialist
Hybrid/Electric Vehicle Systems
Performance Tuning Expert

Research & Community

Actively researches emerging technologies and contributes to automotive forums.

Legal Disclaimer

Important information about using this content

Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.

General Information

The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.

Warranty & Liability

The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.

We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.

Technical Information

All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
Vehicle specifications and procedures may vary by model year, trim level, and region.
Always follow the manufacturer's recommended procedures and safety precautions.
Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
If you're unsure about any procedure, consult a qualified professional mechanic.

Intellectual Property

All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.